Replace Batteries - Wolf Garten LI-ION POWER 60 Notice D'utilisation

Operation
Operating times
Please check noise abatement regulations prevailing in your
country.
Charging the battery
A
General charging instructions
1
Caution! The charger must only be operated in dry
rooms.
Recharge only with the original WOLF-Garten charger (part no.
7087 068)!
Charge the battery before using the mower for the first time.
For charging times, see page 10.
Charging A
1. Connect the charger to the mains socket (230 V~).
2. Insert the charging plug into the charging socket of the battery-
powered shears.
3
Instructions for the handling of the charger
The red LED indicates charge process. When the LED
3 goes out, the lithium-ion battery is charged.
General instructions regarding the battery:
To prolong the service life of the battery, observe the fol-
lowing instructions:
Low battery voltage will reduce the stroke rate of the
shears. In such a case, recharge the battery.
Maintenance
Storage
Make sure to store the battery-powered shears out of the reach
of children.
Always attach the blade guard for transport and storage.
Always recharge the lithium-ion battery prior to any prolonged
period of non-use, i.e. before storing the shears away in winter.
Store the battery-powered shears in a dry and frost-free location.
General instructions
C
1
Caution! Counterrotating blade
Before carrying out any maintenance or cleaning work:
Never actuate the switches
Do not touch the moving blade.
Drive repairs may only be carried out by a WOLF-Garten
service facility!
Cleaning
Clean the battery-powered shears after every use with a dry
cloth. If necessary, use a brush to remove persistent dirt.
Clean and lubricate the gearbox at the end of the gardening sea-
son (see "Cleaning or replacing the blade").
Never clean the battery-powered shears with a water jet.
Cleaning or replacing the blade
D E F G H J K
3
Blunt blades should not be resharpened but replaced.
1. Remove wheels D
Carefully pull the wheels apart until they come off the
rechargeable shears. Then remove the wheels from below.
2. Remove skid E
Lever the retainer (1) upwards and then remove the skid from
the rear (2).
3. Replace cutting head F G H J
Remove the cutting head from the rechargeable shears. Lubri-
cate the plastic ring of the cutter with the lubrication tube (Part of
the „replacement blade package")
G
A :
C (1) (2).
F provided, clean the visible
Always recharge the lithium-ion battery prior to any pro-
longed period of non-use, i.e. before storing the shears
away in winter.
For charging times, see page 10.
In the interest of long battery service life, the device
should not be connected to the charger longer than is ne-
cessary.
The lithium-ion rechargeable battery can be charged at
any charge level and charging can be interrupted at any
time without damaging the battery (no memory effect).
Self-discharge of the battery! Disconnect the plug from
the charger of the battery-powered shears as soon as the
charger is disconnected from the mains.
Adjusting the cutter head
1. Slide the lock button up (1) and then turn the cutter head to the
desired position (2).
2. Release the button (1) and check whether the cutter head is lo-
3 cked in place.
Please note:
The cutter head can be locked in five positions
(90° « 45° « 0° » 45° » 90°).
Switching the battery-powered shears on/off
1. Slide the safety button (1) forward and hold it.
2. Press the control button (2).
3. Release the safety button (1).
4. To switch the battery-powered shears off, release the safety but-
ton (2).
1
Attention! Please follow the safety instructions!
area of the drive, and lubricate this as well with the lubricant pro-
vided. Turn the new cutter head with the plastic ring in the direc-
tion of the drive.
1
Note for shear blades (Accu 8 EM, Accu 10 EM):
Please ensure that the blades are staggered in relationship
to each other H (1).
1
Note for shrub blades (Accu BS EM):
Position the plastic ring in such a way that it is precisely
placed over the eccentric tappet
Push the blade diagonally under the projections
position it in the recharageble shears so that the drill holes of
the blade J sit above the bolts of the rechargeable shears.
4. Fastening the skid E
Push the skid far enough over the rechargeable shears until the
skid retainer snaps in place.
5. Positioning wheels K

Replace batteries

1. Remove cover L
Place a coin in the cover slot and press in the direction of the
blade (1). Remove the cover from above (2).
2. Replace batteries
M
Remove both plugs from the batteries (3); remove the batteries
from the shears. Place the new batteries in the shears and
connect the two plugs.
3. Fastening the cover N
Push the lid with the projection (4) under the edge of the shears
3 and then press the cover on the shears (5).
Note:
Please ensure that no cable protrudes from the shears when
fastening the cover!
B
G .
H
L M N
C
(2) and
13