Care And Maintenance - Baby Jogger CITY MINI 2 Mode D'emploi

UNPACK
EN
1 After unboxing the carrycot, raise the
canopy until it clicks into place, then
undo the four fastening strips around the
canopy.
2 Then remove the mattress, and undo the
six fastening strips around the carrycot
body to remove the liner.
3 Next, pull on the handles inside the
carrycot body to move the support bars
into position. Make sure the support bars
insert into the retaining clips until they
click into place.
Finally, reattach the liner and canopy,
then place the mattress back inside the
carrycot.
FOOT COVER
4 To attach the foot cover, place the foot
cover over the Carrycot frame.
5 Attach the fastening strips on either side
of the carrycot body.
6 On each side of the foot cover, thread
the snap through the loop and close the
snaps together to secure the foot cover
to the carrycot frame.
7 You may also fold the top of the foot
cover down and secure it using the lower
loops.
CANOPY
8 Raise the canopy until it clicks into
position B. Continue to raise the canopy
to position A by pressing the buttons on
either side of the canopy hinge.
WARNING: Before carrying or lifting,
make sure that the canopy is locked into
position A.
NOTE: The canopy has 2 locked positions.
Push and pull the handle to make sure
the canopy is in a locked position. The
canopy can be in any position when
used in the stroller.
9 To lower the canopy, press the buttons
on either side of the canopy hinge then
lower the canopy.
10 To use the canopy window, unzip the
canopy zipper. Then roll the shade up
towards the top.
MOUNTING ADAPTERS
11 Make sure the elastic fabric near the
accessory mounting slots is not covering
the slots.
12 Insert Adapter Brackets into the
corresponding mounting brackets on
your stroller/pushchair. The Adapter
Brackets are secure when they click into
place.
NOTE: Left and right are determined by
standing in front of and facing the
stroller/pushchair and each Adapter
Bracket is labeled with an L or an R for
your convenience.
WARNING: Keep child's hands clear
when installing the adapter brackets.
13 Push the gray release button on each
adapter and pull upward to remove.
NOTE: Remove the adapter brackets before
folding the stroller.
ATTACH TO STROLLER
14 First, recline the backrest by pinching the
clamp behind the backrest, and slide it
down to the lowest position.
15 Pull backrest down on both sides to
match the clamp position.
NOTE: The stroller canopy MUST be
removed before attaching the carrycot.
WARNING: When making adjustments to
the stroller seat, make sure child' s head,
arms, and legs are clear of moving seat
parts and stroller frame.
16 Align the black attachment brackets of
the Carrycot body with the mounting
adapter brackets. The Carrycot body
can only be attached rear facing. Firmly
press down on the carrycot body until
you hear it click into place. Gently pull
up on the canopy handle to ensure it is
locked in place.
17 To remove the carrycot body from
the stroller: Lift the release levers on
each side of the carrycot body and pull
upward to remove.
REMOVING THE INNER FABRIC
18 Unzip the canopy from the handle.
19 Undo the four fastening strips around the
canopy. then remove the canopy fabric.
20 Undo the six fastening strips around the
carrycot body to remove the liner.

CARE AND MAINTENANCE

Mattress Cover & Foot Cover:
• Remove plastic & foam inserts from the
mattress before washing.
• Machine wash separately using a warm
gentle cycle and mild detergent.
• Do not bleach.
• Do not iron.
• Do not place fabric in the dryer. Lay flat
to dry.
Carrycot Base, Canopy & Mattress Pad:
• Wipe clean using a damp cloth.
• Do not bleach.
• Do not iron.
7
EN