ETI C06015301A Guide D'utilisation Et D'entretien

PACKAGE CONTENTS
Part Description
Fixture Body
A
HARDWARE INCLUDED
Part Description
AA Wire Connector
BB Bracket
CC Mounting Screw (for J-box)
DD Mounting Screw (for Bracket)
NOTE: This fixture should be used on a 120 Volt fused circuit only 60Hz.
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing
an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
INSTALLATION
Select the mounting holes according to the size of the J-box. Mount the
1
bracket (BB) to the J-box using the two mounting screws (CC). Pass the
electrical wires from the J-box through the middle hole of the bracket (BB).
J-box
3 Position the screw hole of the fixture body (A) face up, then place the fixture
body (A) on the bracket (BB), ensuring it is close to the wall. Screw the
fixture body (A) to the bracket (BB) using the mounting screw (DD).
BB
A
4 C06018301A and C06018302A can be used in one of two modes: Main
light mode, or nightlight mode. Selecting main light or night light mode by
switching on the wall switch.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so so could lead to electric shock,
fire, or other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit
breaker.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the
receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV technician for
help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.etissl.com.
USE AND CARE GUIDE
RADII VANITY LIGHT
Quantity
1
Quantity
3
1
2
2
BB
CC
DD
A
Questions, problems, missing parts? Call Etissl Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.etissl.com
Model # C06015301A
C06018301A
C06015302A
C06018302A
AA BB
Connect the hot and neutral (black and white) wires from the J-box to the same
2
color wires from the fixture body (A). Wrap the ground wire from the electrical
box around the ground screw on the mounting bracket (BB), then connect to
the green wire from fixture body (A). Cover the wire connections using the wire
connectors (AA). Cover the wire connectors (AA) with electrical tape for a more
secure connection, then position the wires back inside the J-box.
ADJUSTING THE COLOR TEMPERATURE OF THE LIGHT
Choose your favorite correlated color temperature (CCT) from five options: 2700K
warm white, 3000K soft white, 3500K neutral white, 4000K cool white, or 5000K
daylight. Move the toggle switch on the fixture body (A) to make your selection before
inserting into bracket or ceiling.
NOTE: The factory setting for the correlated color temperature (CCT) is 3000K,
which is the warmest white light.
Part # RAVL-24-9CP5-SV-TD-BN
RAVL-24-9CP5NL-SV-TD-BN
RAVL-24-9CP5-SV-TD-MB
RAVL-24-9CP5NL-SV-TD-MB
A
CC DD
AA
BB
Ground Screw