LED ECO
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
NOTE: Two people are recommended for installation of this light fixture.
PACKAGE CONTENTS
Part
Description
Quantity
A
Fixture*
1
* 2x2 Flat Panel model numbers: 64222401/64222402/64222402-I/64222402-EM/64222402-I-EM
* 2x4 Flat Panel model numbers: 64224301/64224302/64224302-I/64224302-EM/64224302-I-EM
* 1x4 Flat Panel model numbers: 64214101/64214102/64214102-I/64214102-EM/64214102-I-EM
HARDWARE AVAILABLE TO PURCHASE
Hardware kits for surface mounting and suspension mounting are sold as separate accessories.
Please contact ETiSSL Customer Service 1-855-384-7754 for additional information.
Part
Description
AA
2-Cable Suspension Mount Kit for 2'x2' panel
BB
3-Cable Suspension Mount Kit for 2'x4' panel
CC
Surface Mounting Kit for 2' x 2' Flat Panel
DD
Surface Mounting Kit for 2' x 4' Flat Panel
EE
Surface Mounting Kit for 1' x 4' Flat Panel
INSTALLATION
NOTICE: Select a suitable location that can support the weight of the fixture. Determine the method of mounting before beginning installation.
CAUTION: Installer is responsible to ensure grid location is rated for fixture weight prior to installation. If uncertain, use cable to support fixture from the retention clips to a suitable
support structure. Failure to do so can cause serious injury.
1
Shut off power at the electrical panel before beginning the installation.
2
Remove existing fixture and set aside to recycle in accordance with local requirements.
Choose your favorite correlated color temperature (CCT) before installing the fixture. Left to right: 3000K/3500K/4000K/5000K
3
NOTICE: The factory setting for the correlated color temperature (CCT) is 4000K, which is the cool white.
Choose the desired brightness (lumen output).
4
NOTICE: The factory setting for the brightness (lumen output) is 4750lm (64222401/64222402/64222402-I/64222402-EM/64222402-I-EM/64224301/64224302/64224302-
I/64224302-EM/64224302-I-EM), and 6250lm (Model # 64214101/64214102/64214102-I/64214102-EM/64214102-I-EM).
MAKING ELECTRICAL CONNECTIONS
Remove the driver box cover plate and punch out the knock out hole.
5
Feed the conduit or Romex (based on local electrical code) through the knock out hole.
6
NOTE: It's recommended to use 16GA pigtails from the terminal block to the
respective power supply wires. Must add pigtail or jumper wires into the ACL and ACN
terminal to use a wire larger than 16AWG for both AC and Neutral Line.
Make the electrical connections:
7
Connect black (L) wire with black wire in the driver.
Connect white (N) wire with white wire in the driver.
Connect ground wire with yellow wire in the driver.
If a 0-10v dimming circuit is available, connect fixture purple wire to driver DIM+ and
gray fixture wire to driver DIM-.
8
Tuck wires inside the driver box and reattach the driver cover.
GRID CEILING INSTALLATION
9a
CAUTION: Clip is used for positioning (NOT for mounting)
Bend each of the mounting clips on the back of the fixture upward and then twist
the top 90°.
Place the fixture into the ceiling grid, hook the mounting clips over the grid ceiling
supports and make sure it is secure.
SUSPENSION MOUNTING
Depending on mounting location, install 4 toggle bolts into drywall or 4 hook
9b
screws into wood.
NOTICE: Toggle bolts are not considered an acceptable means of support in
Canada, in accordance with CSA C22.2 No. 250.4.
NOTICE: There are many installation applications to suspension mount the
fixture. Installer is responsible to ensure mounting accessories and hardware
are compatible with attachment method to surface or structure in accordance
with any local code requirements for installation and inspection.
10b
Attach the aircraft cable to the toggle bolts or hook screws.
Model # 64222401/64222402/64222402-I/64222402-EM/64222402-I-EM/64224301/64224302/64224302-I/
64224302-EM/64224302-I-EM/64214101/64214102/64214102-I/64214102-EM/64214102-I-EM
Part # E16FP-22-LB4-8-CP4-MV-LVD-1PK/E16FP-22-LB4-8-CP4-MV-LVD-2PK/E16FP-22-LB4-8-CP4-
MV-LVD-OS-2PK/E16FP-22-LB4-8-CP4-MV-LVD-EM-2PKE16FP-22-LB4-8-CP4-MV-LVD-EMOS-2PK
E16FP-24-LB4-8-CP4-MV-LVD-1PK/E16FP-24-LB4-8-CP4-MV-LVD-2PK/E16FP-24-LB4-8-CP4-MV-LVD-
OS-2PK/E16FP-24-LB4-8-CP4-MV-LVD-EM-2PK/E16FP-24-LB4-8-CP4-MV-LVD-EMOS-2PK
E16FP-14-LB4-8-CP4-MV-LVD-1PK/E16FP-14-LB4-8-CP4-MV-LVD-2PK/E16FP-14-LB4-8-CP4-MV-LVD-
OS-2PK/E16FP-14-LB4-8-CP4-MV-LVD-EM-2PK/E16FP-14-LB4-8-CP4-MV-LVD-EMOS-2PK
64222401/64222402/64222402-I/64222402-EM/64222402-I-EM/64224301/64224302/64224302-I/
64224302-EM/64224302-I-EM/64214101/64214102/64214102-I/64214102-EM/64214102-I-EM
USE AND CARE GUIDE
FLAT PANELS WITH LUMEN BOOST
16
Quantity
Part #
2
70317201
3
70317202
1
70317101
1
70317102
1
70317103
AND COLOR PREFERENCE
™
Surface Mounting Kits - CC DD and EE
AA
BB
3
Mounting Clip
Ceiling
Fix screw
®
A
A
A
Drill a hole with 6mm
diameter drill bit
Inflatable colloidal particle
Suspension wire fixer
CC
DD
EE