Craftsman CMCPR320 Guide D'utilisation page 11

Pruning Instructions (Fig. A, G)

DANGER:
parts away from the blade. Contact with the blade
will result in serious personal injury.

WARNING:
observe the following:
• Read instruction manual before using. Save
instruction manual.
• Check the shrub for foreign objects such as wires or
fences before each use.
• Keep hand on firmly on tool and other hand far
away from cutting action. Don't overreach.
• Do not use under wet conditions.

CAUTION:
branches greater than 1.25" (32 mm). Use the pruner
only for cutting normal shrubbery around houses
and buildings.
Working Position (Fig. G)
Maintain proper footing and balance and do not overreach.
Wear safety goggles, non‑skid footwear and gloves when
pruning. Hold the tool firmly. Always hold the pruner, as
shown in Fig. G. Refer to Proper Hand Position for more
information. Never hold the tool by the blades.
1. Position the branch to be cut between the cutting
blade 5 and fixed blade
2. Push the lock‑off button
off switch then squeeze the trigger switch
3
3. The cutting blade 5
branch off.
nOTE: Cut branches at an angle for a cleaner cut.
4. Release the trigger switch.
nOTE: If more branches need to be cut, at the same
time, the lock‑off switch
actuate the trigger switch
repeat steps 1‑4..
MAINTENANCE

WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Keep hands and other body
To guard against injury,
Do not use blade to cut
6 .
down and squeeze the lock‑
2
1
will make a cut cycle and cut the
can be held down and
3
as needed. Otherwise,
1
To reduce the risk of serious
Removing and Installing Blade (Fig. A, H, I)

DANGER:
REASSEMBLING THE BLADE SYSTEM, ENSURE EACH
PART IS REINSTALLED CORRECTLY, AS DESCRIBED
BELOW. IMPROPER ASSEMBLY OF THE BLADE OR
OTHER PARTS OF THE BLADE SYSTEM CAN CAUSE
SERIOUS INJURY.

DANGER:
personal injury, turn unit off, remove battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause serious personal injury.

WARNING:
protection. Be careful of the sharp edges on the blade.
Replacement blades are available from your nearest
authorized service center. This pruner requires replacement
blade CMZPRB300.
1. Remove the battery.
2. Wear proper eye protection and gloves and be careful
not to cut yourself.
3. Place the product on a smooth, level surface.
4. Remove the nut cap
nOTE: If the nut cap is difficult to remove, a 5 mm hex
wrench (not included) can be used to remove it.
5. Slide out the blade cover
6. Remove the cutting blade
7. Install the new cutting blade.
.
nOTE: Ensure the cutting edge faces toward the fixed
cutting blade as shown in Fig. I.
8. Reinstall the blade cover.
9. Screw the nut cap back in clockwise, making sure it is
secure.
Blade Maintenance (Fig. J)

WARNING:
protection while removing, sharpening, and installing blade.
The cutting blades are made from high quality, hardened
steel and with normal usage, they will not require
resharpening. However, if you accidentally hit a wire fence,
stones, glass, or other hard objects, you may put a nick in the
blade. There is no need to remove this nick as long as it does
not interfere with the movement of the blade. If you drop
the trimmer, carefully inspect it for damage. If the blade is
bent, housing cracked, handles broken or if you see any other
condition that may affect the tool's operation contact your
local authorized service center for repairs before putting it
back into use.
1. Remove the battery.
2. Remove blade from pruner. See instructions for
Removing and Installing Blade.
RISK OF INJURY. WHEN
To reduce the risk of serious
Use gloves and proper eye
by turning it counterclockwise.
9
10 .
as shown in Fig. I.
5
Use gloves and proper eye
English
9