Télécharger Imprimer la page
Empire Heating Systems DV55E-6 Instructions D'installation Et Manuel Du Propriétaire
Empire Heating Systems DV55E-6 Instructions D'installation Et Manuel Du Propriétaire

Empire Heating Systems DV55E-6 Instructions D'installation Et Manuel Du Propriétaire

Publicité

Liens rapides

INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
WARNING
FIRE OR EXPLOSION HAZARD
If the information in these instructions is
not followed exactly, a fire or explosion
may result causing property damage,
personal injury or loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch;
do not use any phone in your building.
Leave the building immediately.
Immediately call your gas supplier
from a neighbor's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fire department.
— Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
This appliance may be installed as an OEM
installation in a manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer's
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280, in the United States, or the
Mobile Home Standard, CAN/CSA Z240 MH
Series, in Canada.
This appliance is only for use with the
type(s) of gas indicated on the rating plate. A
conversion kit is supplied with the appliance.
NOTICE: Contact your dealer for installation, service, repair, or warranty claim
Empire Comfort Systems does not sell, service, or provide warranty directly to consumers. The consumer must contact the dealer where the
product was purchased for a warranty claim. If a non-qualified installer or consumer installs or services this product, the product warranty is
voided. Most dealers will only service products they sold so it is important for the consumer to choose a qualified dealer for installation and
warranty service. In order to maintain the warranty, service must be performed annually and documentation reviewed during the warranty request.
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
FAN TYPE DIRECT - VENT
WALL FURNACE
FOR INSTALLATION IN
MANUFACTURED (MOBILE HOME),
MODULAR OR RESIDENTIAL HOMES
MODELS:
DV55E - 6
WARNING
If not installed, operated and maintained in
accordance with the manufacturer's instructions,
this product could expose you to substances in
fuel or from fuel combustion which can cause
death or serious illness.
Patent # 5.664.555

Publicité

loading

Sommaire des Matières pour Empire Heating Systems DV55E-6

  • Page 1 INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL FAN TYPE DIRECT - VENT INSTALLER: Leave this manual with the appliance. WALL FURNACE CONSUMER: FOR INSTALLATION IN Retain this manual for future reference. MANUFACTURED (MOBILE HOME), MODULAR OR RESIDENTIAL HOMES WARNING MODELS: FIRE OR EXPLOSION HAZARD DV55E - 6 If the information in these instructions is not followed exactly, a fire or explosion...
  • Page 2 TABLE OF CONTENTS SECTION PAGE Important Safety Information ............................. 3 Safety Information for Users of Propane Gas ......................4 Requirements for Massachusetts ..........................5 Introduction ................................6-7 Specifications ................................7 Gas Supply ................................8 Gas Conversion Instructions ............................. 9 Clearances ................................10 Furnace Installation ............................
  • Page 3 IMPORTANT SAFETY INFORMATION THIS IS A HEATING APPLIANCE DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED. • Due to high temperatures the appliance should be • Installation and repair should be done by a QUALIFIED located out of traffic and away from furniture and SERVICE PERSON.
  • Page 4 SAFETY INFORMATION FOR USERS OF PROPANE GAS Propane is a flammable gas which can cause fires and Someday when there may not be a minute to lose, everyone's explosions. In its natural state, propane is odorless and safety will depend on knowing exactly what to do. If, after colorless.
  • Page 5 REQUIREMENTS FOR MASSACHUSETTS For all side wall horizontally vented gas fueled equipment 3. SIGNAGE. A metal or plastic identification plate shall be installed in every dwelling, building or structure used in whole permanently mounted to the exterior of the building at or in part for residential purposes, including those owned or a minimum height of eight (8) feet above grade directly operated by the Commonwealth and where the side wall...
  • Page 6 INTRODUCTION Introduction Qualified Installing Agency Always consult your local Building Department regarding Installation and replacement of gas piping, gas utilization regulations, codes or ordinances which apply to the installation equipment or accessories and repair and servicing of of a direct vent wall furnace. equipment shall be performed only by a qualified agency.
  • Page 7 INTRODUCTION (CONT'D) When an existing Category 1 heater is removed or replaced, also indicate effects of an improperly sized venting system the original venting system may no longer be sized to (formation of condensate, leakage, spillage, etc.) and shall properly vent the attached appliances. Instructions shall specify the following test procedure: WARNING CARBON MONOXIDE POISONING HAZARD...
  • Page 8 GAS SUPPLY Consult the current National Fuel Gas Code, ANSI Z223.1 Installing a New Main Gas Shut-Off CAN/CGA-B149 (.1 or .2) installation code. Each appliance should have its own manual gas shut-off. A manual main gas shut-off should be located in the vicinity RECOMMENDED GAS PIPE DIAMETER of the unit.
  • Page 9 GAS CONVERSION INSTRUCTIONS WARNING Conversion must be done by a qualified service technician. Main burner orifice(s) and new gas conversion label are provided in conversion kit attached to manifold pipe. CONVERSION INSTRUCTIONS FROM PROPANE GAS TO NATURAL GAS Make sure gas supply to furnace is off prior to conversion and GAS VALVE SWITCH disconnect electrical power to unit.
  • Page 10 CLEARANCES 1. Pick a location on a wall with a clear space of 36" (91.4cm) The bottom of the exhaust vent terminal and the air intake high by 43" (109cm) wide in the room. In selecting shall be located at least 12" (305mm) above grade and must a location for installation, it is necessary to provide be vented outside.
  • Page 11 FURNACE INSTALLATION (CONT'D) 10” (254mm) 4" (102mm) 4" (102mm) CASING CASING 4" (102mm) 4" (102mm) 4" (102mm) 4" (102mm) WALL WALL CASING CASING CASING CASING WALL MOUNTING BRACKET WALL MOUNTING BRACKET BACK BACK WALL WALL WALL MOUNTING BRACKET WALL MOUNTING BRACKET BACK BACK BACK...
  • Page 12 FURNACE INSTALLATION (CONT'D) Venting (Figures 7 and 8) ATTENTION: If the right shroud and left shroud are installed This unit is vented directly out the back using the concentric incorrectly, with the 3/4" wide flanges facing inward, the top vent tube assembly provided. See Figure 2 for vent hole shroud will not be able to be installed onto the side shrouds.
  • Page 13 LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE OPERATING WARNING If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance does not have a pilot. It is equipped C.
  • Page 14 WIRING GV = GAS VALVE LS = LIMIT SWITCH FS = FLAME SENSOR XFMR = TRANSFORMER PS = PRESSURE SWITCH IGN = HOT SURFACE IGNITOR ROS = ROLLOUT LIMIT SWITCH OPTIONAL WALL MOUNT THERMOSTAT DISCONNECT INTEGRAL THERMOSTAT "R", "W", AND "C" LEADS AND ATTACH WALL THERMOSTAT AS SHOWN CORDSET 115 VAC XFMR BLACK HOT...
  • Page 15 MAINTENANCE Proper Main Burner Flame Removing Gas Valve The proper main burner flame will be a blue primary (inner) 1. Remove front grill assembly. flame with a larger, lighter blue secondary (outer) blue flame. 2. Disconnect manifold union assembly at gas valve. 3.
  • Page 16 OPERATION AND TROUBLESHOOTING Your new furnace should provide many years of trouble free 3. After the furnace operates and satisfies the thermostat, the performance, however, a yearly inspection of the burners , gas valve closes and the circulating air blower continues flue passageways and the outlet vent assembly should be to run for about 2 minutes and then shuts off.
  • Page 17 FURNACE CONTROL BOARD DIAGNOSTICS FAULT SEQUENCE CODE — TROUBLE SHOOTING GUIDE # Of Blinks Fault Condition Fault Correction Steady On Control OK -Check Circulating Air Blower Inlet or Grill Outlet for Blockage, Inducer Blower/Circulating Air Blower Run to Cool Heat Ex- changer and Limit 1 Flash Temperature limit switch is open...
  • Page 18 HOW TO ORDER REPAIR PARTS Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the service person/dealer. All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment.
  • Page 19 PARTS VIEW 11 11 11 11 45355-0-1023 Page 19...
  • Page 20 WARRANTY Empire Comfort Systems Inc. warranties this space heating product to be free from defects at the time of purchase and for the periods specified below. Space heating products must be installed by a qualified technician and must be maintained and operated safely, in accordance with the instructions in the owner’s manual.
  • Page 21 INSTRUCTIONS POUR L'INSTALLATION ET MANUEL DU PROPRIÉTAIRE RADIATEUR MURAL À INSTALLATEUR : CIRCULATION FORCÉE Laissez cette notice avec l’appareil. CONSOMMATEUR : AVEC UN ÉVENT DIRECT Conservez cette notice pour consultation ultériure. POUR L’INSTALLATION DANS DES MAISONS PRÉ - FABRIQUÉES AVERTISSEMENT (MAISON MOBILE), MODULAIRES OU RÉSIDENTIELLES RISQUE D’INCENDIE OU D’EXPLOSION...
  • Page 22 LA TABLE DES MATIÈRES TABLE OF CONTENTS SECTION PAGE Information Importante de Sécurité ......................3 Information de Sécurité pour les Utilisateurs de Propane ................. 4 Introduction ............................5-6 Spécifications ............................. 6 Alimentation en Gaz ...........................7 Les Instructions Pour La Conversion des Gaz ................... 8 Clearances ..............................9 Installation du Radiateur ........................
  • Page 23 INFORMATION IMPORTANTE DE SÉCURITÉ CECI EST UN APPAREIL DE CHAUFFAGE NE PAS FAIRE FONCTIONNER CET APPAREIL SANS QUE LE PANNEAU DU DEVANT SOIT INSTALLÉ. • A cause des hautes températures, cet appareil doit être situé • L'installation et la réparation doivent être faites par une dans un endroit non achalandé...
  • Page 24 INFORMATION DE SÉCURITÉ POUR LES UTILISATEURS DE PROPANE Le propane est un gaz inflammable qui peut causer des incendies et Un jour, quand il n’y aura peut-être pas une minute à perdre, la sécurité de tout le monde dépendra de savoir exactement quoi faire. des explosions.
  • Page 25 INTRODUCTION Introduction Installation dans les Garages Résidentiels Toujours consulter le département de construction de votre région Tous les équipements dans les garages résidentiels employant en ce qui regarde les règlements, les codes ou les ordonnances qui du gaz, doivent être installés de façon à ce que les brûleurs et les s'appliquent à...
  • Page 26 INTRODUCTION (SUITE) Lorsqu'un radiateur de catégorie 1 existant est retiré ou remplacé, le également indiquer les effets d'un système de ventilation de taille système de ventilation d'origine peut ne plus être dimensionné pour inadéquate (formation de condensat, fuite, déversement, etc.) et doivent ventiler correctement les appareils raccordés.
  • Page 27 ALIMENTATION EN GAZ Consulter le Code d’Installation en Cours du National Fuel Gas Installation d’un Nouveau Robinet Principal pour le Gaz Chaque appareil doit avoir son propre robinet manuel de gaz. Code, ANSI Z223.1 CAN/CGA-B149 (.1 ou .2). Dans le Commonwealth de Massachusetts, le robinet de gaz doit LE DIAMÈTRE RECOMMANDÉ...
  • Page 28 INSTRUCTIONS DE CONVERSION DE GAZ AVERTISSEMENT Conversion doit être faite par un technicien d’entretien qualifié. Les orifices du brûleur principal et la nouvelle étiquette pour le changement des gaz sont fournis dans l’ensemble de conversion qui est attaché au tuyau de gaz. LES INSTRUCTIONS POUR LA CONVERSION DU GAZ PROPANE AU GAZ NATUREL Assurez-vous que l’alimentation en gaz de la fournaise est éteinte avant INTERRUPTEUR DE SOUPAPE DE GAZ...
  • Page 29 CLEARANCES 1. Choisissez un endroit sur un mur qui aura un espace libre de 36” Le bas de l'évent terminal d'échappement et l'entrée d'air doit être (91.4cm) de haut par 43” (109cm) de large. En choisissant un situé à au moins 12” (305mm) au dessus du niveau du sol et doit emplacement, il est nécessaire de fournir l'espace libre adéquat être évacuer dehors.
  • Page 30 10” (254mm) 4” (102mm) PAROI ARRIÉRE SUPPORT DE MONTAGE MURAL #10 X 1” #10 X 1/2” SUPPORT MURAL #10 X 1/2” Figure 4 Figure 6 Installation du Support Mural (Figures 5 and 6) Après avoir trouver l'emplacement du radiateur, l'alimentation de gaz et l'évent, le support mural doit être placé...
  • Page 31 INSTALLATION DU RADIATEUR (SUITE) Les vis sont fournies dans le paquet de quincaillerie. Insérez le Évacuation (Figures 7 and 8) filtre à air dans la paroi du dessus. L'évacuation des gaz de cet appareil est faite directement à l'arrière en utilisant un ensemble de tuyau d'évent concentrique, fourni avec ATTENTION: Si la paroi du côté...
  • Page 32 INSTRUCTIONS D’ALLUMAGE POUR VOTRE SÉCURITÉ, LIRE AVANT D'ALLUMER AVERTISSEMENT Si vous ne suivez pas exactement ces instructions, un feu ou une explosion peut se produire causant des dommages à la propriété, des blessures corporelles ou la mort. A. Cet appareil n’a pas de veilleuse. Il est muni d’un dispositif •...
  • Page 33 WIRING SCHÉMA DE CÂBLAGE AVERTISSEMENT: DÉBRANCHER L'ALIMENTATION ÉLECTRIQUE AVANT TOUTE INTERVENTION GV = ROBINET DE GAZ LS = CONTACT FIN DE COURSE FS = CAPTEUR DE FLAMME XFMR = TRANSFORMATEUR PS = MANOCONTACT THERMOSTAT MURAL EN OPTION IGN = ALLUMEUR SURFACE CHAUDE DÉBRANCHER LES FILS “R”, “W”...
  • Page 34 MAINTENANCE Aspect Convenable de la Flamme du Brûleur Principal 1. Enlever l'assemblage du grillage avant. La flamme convenable pour le brûleur principal consistera 2. De la valve de gaz, débrancher le raccord du tuyau de gaz. d'une flamme (intérieure) primaire bleue avec une flamme 3.
  • Page 35 FONCTIONNEMENT ET DÉTECTION DES DÉFECTUOSITÉS Votre nouveau radiateur vous apportera plusieurs années de 3. Après que le radiateur fonctionne et que le thermostat atteint performance sans trouble, par contre, une inspection annuelle des la température satisfaisante, la valve de gaz se ferme et la brûleurs, des tuyaux d'évacuation et l'ensemble d'évent extérieur soufflerie continue de fonctionner pour à...
  • Page 36 DIAGNOSTIC DU CIRCUIT DE COMMANDE DE CHAUDIÈRE CODE D’ERREUR SÉQUENTIEL — GUIDE DE DÉPANNAGE CLIGNOTEMENTS ÉTAT D’ERREUR CORRECTION DE L’ERREUR Allumé Commande OK en continu 1 clignotement Le rupteur thermique est ouvert -Vérifier l’absence d’obstruction de l’admission ou la grille de refoulement de soufflante d’air de chauffage, conduite de soufflante d’induction/air de chauffage vers échangeur et rupteur -Voir s’il y a un retour de flamme causant l’ouverture du limiteur de...
  • Page 37 LISTE DES DISTRIBUTEURS DE PIÈCES PRINCIPAUX Pour commander des pièces sous garantie, adressez-vous au revendeur Empire local. Veuillez voir le concessionnaire au www.empire- comfort.com. Pour assurer un service sous garantie, le revendeur doit connaître votre nom, votre adresse, la date d’achat et le numéro de série du produit, ainsi qui la nature du problème.
  • Page 38 FAÇON DE COMMANDER LES PIÈCES DE RÉPARATION Les pièces peuvent être commandées seulement par l'entremise du technicien d'entretien ou du vendeur. Pour de meilleurs résultats, le technicien d'entretien ou le vendeur devrait commander les pièces chez le distributeur. Les pièces peuvent être expédiées directement au technicien d'entretien ou au vendeur.
  • Page 39 VUE DES PIÈCES 11 11 11 11 45355-0-1023 Page 19...
  • Page 40 GARANTIE Empire Comfort Systems Inc. garantit que ce produit de chauffage individuel est exempt de défauts au moment de son achat et pendant les périodes indiquées ci-dessous. Les produits de chauffage individuel doivent être installés par un technicien qualifié et doivent être entretenus et utilisés de façon sécuritaire, en conformité...