Cleaning & Maintenance; Accessories - Metabo Rbe 15-180 Mode D'emploi

en ENGLISH
Positions 1-6 correspond approximately to the
following belt speeds:
RBE 15-180
1 ........ 8.4 m/s
2 ........ 12.5 m/s
3 ........ 16.5 m/s
RBVB 18 LTX BL 180:
1 ........ 5.0 m/s
2 ........ 7.0 m/s
3 ........ 10.0 m/s
6.3 Sanding belt replacement
See illustration on page 3.
- Release the tensioner arm (6) and remove the
sanding belt (7).
- Place the new sanding belt on the rollers such that
its direction of circulation (arrows on the inside of
the sanding belt) matches the arrow (10) on the
gearbox.
- Release the tensioner arm (6).
- Ensure that the sanding belt is completely on the
rollers.
6.4 Sanding procedure
Place the machine on the material such that the
sanding belt is parallel to the surface of the
workpiece.
When working, please ensure that the machine is
operated at right angles to the pipe so that the belt
does not fall off the rollers.
Using the additional handle, the belt can be pressed
against the pipe and at same time placed around it.
The angle of contact and the cutting output may be
changed by the contact pressure.
Keep the machine in constant motion because
otherwise recesses could be produced in the
material.
7. Cleaning, maintenance
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
8. Troubleshooting
8.1 Mains powered machines
The electronic signal indicator (4) lights
up and the load speed decreases. There is
too much load on the machine! Run the
machine in idling until the electronic signal indicator
switches off.
The machine does not start.The
electronic signal indicator (4)
flashes.Restart protection is active. If the
mains plug is inserted with the machine switched on
or if the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and back on again.
8
4....... 20.6 m/s
5....... 24.6 m/s
6....... 28.8 m/s
4....... 13.0 m/s
5....... 15.0 m/s
6....... 18.0 m/s
8.2 Cordless machines
The electronic signal display (4) flashes
and the machine does not start.
The battery pack is empty; the temperature is
too high or the restart protection has triggered.
Switch the machine off and back on again.
The machine will not start if the battery pack is
inserted while the machine is on.
When using a battery pack that is not part of CAS,
the machine will not start.
The electronic signal display (4) is
permanently on.
There has been an overload while working,
therefore the performance may be reduced
temporarily. Reduce working pressure.
Electronic safety shutdown: the machine has
SHUT DOWN by itself. If the slew rate of the
current is too high (for example, if the machine
suddenly seizes or kickback occurs), the machine
switches off. Switch off the machine. Switch it on
again and continue to work as normal. Try to
prevent the machine from seizing.

9. Accessories

Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
If you need any accessories, check with your
dealer.
For the dealer to select the correct accessory, they
need to know the exact model designation of your
power tool.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625549000 10.0 Ah (LiHD)
etc.
Order no.: 625591000 4.0 Ah (LiPOWER)
Order no.: 625028000 5.2 Ah (LiPOWER)
etc.
Chargers: ASC 55, ASC 145, etc.
For the complete range of accessories, see
www.metabo.com or the main catalogue.
10. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from Metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.