Numark iCDX Guide D'utilisation page 8

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Parameter Knob Features
Several menus and options can be accessed by holding down one of the buttons listed below and turning
the parameter knob.
Scratch
Holding the SCRATCH button and turning the
parameter knob will allow you to choose the
desired scratch mode:
Vinyl: This mode allows you to use the
platter to scratch just like you would with
a vinyl record.
When you press on the
inner part of the jog wheel, the music
will stop where it is until the wheel is
released.
Forward: When you use the jog wheel
to scratch, only the forward motions are
heard. This simulates using a crossfader
to cut out the backspins.
Bleep: Allows you to "insert" a scratch
while the music continues to advance.
One you are done scratching, the music
will continue to play where it would have
been if you hadn't scratched.
Bleep
Forward:
combination
of
scratch modes. Allows you to "insert" a
scratch
but
only
motion of the platter.
Cue:
Scratches from the current cue
point.
Each time you touch the inner
platter, the song will begin from the
current cue point. This allows you to set
a cue point for a certain segment of a
song and scratch repeatedly over the
same segment.
Cue
Forward:
combination of Cue mode and Forward
mode. It scratches from the current cue
point but does not play sound during
counter clockwise motion of the wheel.
Pitch
Holding the PITCH button and turning the
parameter knob allows you to change change
the key of the current song from "L" (lower
key) to "H" (higher key) in 40 semitone
increments (with 0 being no key change).
Mode
To turn relay mode on and off, hold the
rectangular
MODE
parameter knob to select the appropriate relay
setting. Relay mode will allow you to alternate
play between 2 compatible units connected via
a 1/8" mono relay/remote cable.
Essentially
Bleep
and
Forward
plays
the
forward
Cue
forward
is
itch
ode
button
and
turn
Search
Search speed can be adjusted by holding
SEARCH and rotating the parameter knob.
Options based upon 1 wheel rotation are 15
seconds, 30 seconds, and 1 minute.
Program / Parameter Options
Holding the PROGRAM button and turning the
parameter knob will bring you to the following
menu options. Pressing down on the
parameter knob will allow you to modify the
parameters for the menu option that you have
selected:
Next Track Fade Time (On, Off, 1s, 2s,
3s): Turning this option on will allow you
to automatically fade from one track to
the next. If you select "On", you will
then be prompted to enter the desired
fade time from 1 to 3 seconds.
a
Scratch Delay (On, Off): Activates a
slight delay when releasing the platter in
scratch mode.
Remote (On-On, On-Off, Fader Start):
Changes the remote start option to allow
the unit to be started by another device
using a remote start cable.
Power On Play (On, Off): When on,
this option will cause the CD player to
begin playing as soon as the power is
turned on.
a
Memo All Clear (No, Yes): Clears all
stored cue points and loop point
information.
Sleep Mode (On, Off): When sleep
mode is engaged the unit will go into a
"sleep" state after a few minutes of
inactivity.
Preset Clear (Yes, No): Reset all global
parameters to their default settings.
Version Number: When the parameter
knob is pressed, the operating system
version numbers will be displayed for as
long as the PROG button is held.
Power On Demo (On, Off): When this
option is on, the unit will go into a "demo
mode" where the platter LEDs will
the
illuminate in a pattern as soon as the
unit is powered on.
6
earch

Publicité

Table des Matières
loading

Table des Matières