Applications; Installation And Connection - Monacor M-32CD Mode D'emploi

Masquer les pouces Voir aussi pour M-32CD:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

2 Safety Notes
GB
The CD player module corresponds to all relevant
directives of the EU and is therefore marked with
G
The module is suitable for indoor use only. Pro-
tect it against dripping water and splash water,
high air humid ity and heat (admissible ambient
temperature range 0 – 40 °C).
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the module and no lia-
bility for any resulting personal damage or mate-
rial damage will be accepted if the module is
used for other pur pos es than originally intended,
if it is not correctly operat ed or not installed or
repaired in an expert way.
If the module is to be put out of operation
defin itively, take it to a local recycling plant
for a disposal which will not be harmful to
the environment.

3 Applications

The CD player module M-32CD is provided for
installation into a basic unit (e. g. active system,
amplifier) and offers extensive functions, such as
continuous repeat, random replay, programming of
an individual title sequence, purposeful selection of
folders (file directories) on MP3 CDs.
It is able to play audio CDs, audio CDs you
have burnt yourself (audio CD-R), and CDs with
titles in MP3 format. However, problems may occur
when replaying rewriteable CDs (CD-RW), de -
pending on the type of CD, the CD burner used,
and the burning programme.
The USB interface allows to replay MP3 files
from a hard disk or a USB flash drive.
4

Installation and Connection

G
The CD player module must only be installed by
qual ified personnel!
G
The module must be installed into the basic unit
in a horizontal way.
1) Prior to the installation of the module, always
disconnect the basic unit from the 230 V mains.
2) To accommodate the module, make a cutout of
155 mm × 50 mm on the basic unit.
3) Make the electrical connection to the basic unit:
10
Marking
.
+12 V
GND
L-CH
S-GND
R-CH
4) Slide the module through the cutout on the basic
unit and fix it via its front panel with four screws
5 Operation
5.1 Remote control
1) To insert the batteries (2 × 1,5 V, size AAA),
remove the battery compartment cover on the
rear side of the remote control. Insert the batter-
ies as indicated in the battery compartment.
Close the compartment with the cover.
If the remote control is not in use for a longer
period of time, remove the batteries to prevent
any damage due to battery leakage.
2) When you press a button on the remote control,
always direct the remote control towards the
sensor REMOTE (8). There must be no obsta-
cles between the remote control and the sensor.
3) If the range of the remote control decreases, the
batteries are exhausted and must be replaced.
Used batteries must not be placed in
the household waste; always take them
to a special waste disposal, e. g. collec-
tion container at your retailer.
5.2 Replaying music titles
After applying the 12 V operating voltage, the CD
player is switched on. The display (7) will show
"Welcome".
First the player will read the CD. If no CD has
been inserted, the player will read the USB flash
drive. If no USB flash drive has been connected
either, the display will show "NO DISC".
1) Insert a CD with the lettering facing up into the
slot (1) until it is pulled in automatically
and / or
connect a USB flash drive to the USB port (6) or
connect a hard disk (with individual power sup-
ply, if required) to the USB port.
Core colour
Connection for
Operating Voltage
red
+12 V (0.8 A)
black
ground
Audio Output
white
left channel
black
ground
red
right channel

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

17.3350

Table des Matières