Other Information; Wireless Display; Connecting Other Wireless Devices - VESTEL IF75T633/6 Manuel D'utilisation

If the selected network is protected with a password,
please enter the correct key by using the virtual
keyboard. You can use this keyboard via the directional
buttons and the OK button on the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established.
To disconnect from a wireless network, highlight
Network Type and press Left or Right buttons to set
as Disabled.
If your router has WPS (Wi-Fi Protected Setup) button,
you can directly connect your Display to the modem/
router without entering a password or adding the
network first. Highlight the Press WPS on your wifi
router option and press the OK button. Then press
the WPS button on your router/modem to connect.
Highlight Internet Speed Test and press the OK button
to check your internet connection speed. Highlight
Advanced Settings and press the OK button to open
the advanced setting menu. Use directional and numeric
buttons to set. Press the OK button to save settings
when complete.

Other Information

The status of the connection will be displayed as
Connected or Not Connected and the current IP
address, if a connection is established.
Connecting to your mobile device via WiFi
• If your mobile device has WiFi feature, you can connect
it to your Display via a router, in order to access the
content in your device. For this, your mobile device
must have an appropriate sharing software.
• Connect to your router following the steps stated above
in the Wireless Connectivity section.
• Afterwards, engage your mobile device with the router
and then activate the sharing software on your mobile
device. Then, select files that you want to share with
your Display.
• If the connection is established correctly, you will be
able to access the shared files from your mobile device
via the Media Browser of your Display.
• Enter the Media Browser menu and the playback
device selection OSD will be displayed. Select your
mobile device and press the OK button to continue.
• If available, you can download a virtual remote
controller application from the server of your mobile
device application provider.
Note: This feature may not be supported on all mobile devices.

Wireless Display

Wireless Display is a standard for streaming video
and sound content by Wi-Fi Alliance. This feature
provides the ability to use your Display as wireless
display device.
Using with mobile devices
There are different standards which enable sharing of
screens including graphical, video and audio content
between your mobile device and Display.
Plug the wireless USB dongle to Display first, if the
Display doesn't have internal WiFi feature.
Then press the Source button on the remote and
switch to Wireless Display source.
A screen appears stating that the Display is ready
for connection.
Open the sharing application on your mobile device.
These applications are named differently for each
brand, please refer to the instruction manual of your
mobile device for detailed information.
Scan for devices. After you select your Display and
connect, the screen of your device will be displayed
on your Display.
Note: This feature can be used only if the mobile device
supports this feature. Scanning and connecting processes
differ according to the programme you use. Android based
mobile devices should have the software version V4.2.2
and above.

Connecting Other Wireless Devices

Your Display supports another short range wireless
connection technology too. A pairing is required before
using these kind of wireless devices with the Display
set. You should do the followings to pair your device
with the Display:
• Set the device to pairing mode
• Start device discovery on the Display
Note: Refer to the user manual of the wireless device to learn
how to set the device to pairing mode.
You can connect audio
Display. Unplug or switch off any other connected
audio device in order for wireless connection feature
to work correctly. For audio devices you should use
the Audio Link option in the System>Sound menu.
Select the menu option and press the OK button to
open the related menu. Using this menu you can
discover and connect the devices that use the same
wireless technology and start to use them. Follow the
on-screen instructions. Start the device discovery. A
list of available wireless devices will be displayed.
Select the device you want to connect from the
list and press the OK button to connect. If "Device
connected" message is displayed, the connection
is successfully established. If the connection fails
try it again.
Note: Wireless devices may operate within the same radio
frequency range and may interfere with one another. To
improve the performance of your wireless device place it at
least 1 meter away from any other wireless devices.
English - 19 -
devices wirelessly to your