JB Systems Light Space-3 Laser Mode D'emploi page 6

ENGLISH
These are the functions available on the CA-8 controller:
 STANDBY button: used to put the laser in blackout (no output). The standby LED
is on during blackout.
 MODE button: used to toggle different modes:
 MODE LED OFF: Laser in full automatic mode. Function button is not used.
 MODE LED ON: Laser in manual pattern select mode. Press the function
button to select one of the built-in patterns.
 MODE LED BLINKING: Laser is in Music controlled mode. Function button is
not used.
5) DMX512 MODE:
The laser can be controlled by any standard DMX-controller in 2 different DMX-modes:
 1 CHANNEL MODE: for extremely easy setup and use! (display shows "1Ch")
 8 CHANNEL MODE: for full control of all possibilities. (display shows "8Ch")
 Connect the DMX input of the laser to the DMX output of the previous unit in the chain
or directly to the DMX-output of your controller.
 Press the FUNC-button until the display shows: "1Ch" or "8Ch".
 Press the UP/DOWN buttons to select the desired DMX-mode. (1Ch or 8Ch)
 Press the ENTER-button to confirm your choice.
 Press the FUNC-button until the display shows a 3 digit number
 Select the desired DMX-address (from 001 to 505)
 Press the ENTER-button to confirm your choice.
The Space3 laser uses 8channels, please refer to the DMX-chart below for the functions
of the different channels.
Note: the display blinks when the unit is in DMX-mode and no DMX-signal is detected.
Some more information on DMX512:
The DMX-protocol is a widely used high speed signal to control intelligent light
equipment. You need to "daisy chain" your DMX controller and all the connected light
effects with a good quality XLR M/F balanced cable. To prevent strange behavior of the
light effects, due to interferences, you must use a 90Ω to 120Ω terminator at the end of
the chain. Never use Y-splitter cables, this simply won't work!
Each effect in the chain needs to have its proper starting address so it
knows which commands from the controller it has to decode.
1 CHANNEL DMX-CONFIGURATION OF THE LASER:
CHANNEL VALUE DESCRIPTION
120  255 MUSIC mode
1 020  119 AUTO mode
000  019 Laser off (black out)
JB SYSTEMS
®
USER MANUAL
7/54 SPACE 3 Laser
ENGLISH
8 CHANNEL DMX-CONFIGURATION OF THE LASER:
CHANNEL VALUE DESCRIPTION
1 000-063 Laser output in blackout
MODE 064-127 Laser in Music controlled mode
SELECT 128-191 Laser in Full automatic mode
192-255 Laser in DMX mode
2 000-063 Pattern Group 1: LINES
PATTERN 064-127 Pattern Group 2: TUNNELS
GROUP 128-191 Pattern Group 3: CURVES
192-255 Pattern Group 4: OTHERS
3 SEE CH2: LINES
PATTERN
SELECT
000-031
032-063
064-095
096-127
128-159
160-191
192-233
234-255
4 000-128 Fixed rotation position of the pattern
ROTATION 129-255 Continuous pattern rotation from slow to fast
5 000-128 Zooming: pattern size (from big to small)
SIZE 129-255 Continuous pattern zooming (from slow to fast)
6 000-128 Pan movement (X-axis: horizontal movement)
PAN 129-255 Pan speed (from slow to fast)
7 000-128 Tilt movement (Y-axis: vertical movement)
TILT 129-255 Tilt speed (from slow to fast)
8 000-085 Original pattern (selected with channels 2+3)
OPTION 086-170 Patterns without blanking (all pattern lines connected together)
171-255 Black out of the laser beam (laser beam OFF)
JB SYSTEMS
®
USER MANUAL
TUNNELS CURVES OTHERS
8/54 SPACE 3 Laser