Maintenance And Service; Maintenance And Cleaning - Bosch GTA 2500 Compact Professional Notice Originale

OBJ_BUCH-1463-003.book Page 12 Monday, November 14, 2016 1:03 PM
12 | English
Assembly
Delivery Scope
Please also observe the representation of
the delivery scope at the beginning of the op-
erating instructions.
Before assembling the saw stand, check if all
parts listed below are provided:
No. Designation
Saw stand GTA 2500 Compact
5 Attachment set
1 Workpiece support
10 Open-end spanner
15 Power tool fastening kit
consisting of:
– Hexagon bolt (M8 x 45)
– Washer
Assembling the Saw Stand
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packaging material.
Setting Up the Saw Stand (see figures A1–A2)
– Lay the saw stand upside down on the floor (legs facing up-
ward).
– Push the locking pin 11 in and tilt the leg upward until the
locking pin can be heard to engage.
– Repeat this workstep with the other three legs.
– Turn around the saw stand to the working position.
– Ensure that the saw stand is stable and that all locking pins
have engaged.
The saw stand is easily aligned with the height-adjustable leg
8.
– Screw the leg in or out until the saw stand is aligned level
and all four legs face against the floor.
Mounting the Workpiece Support (see figure B)
– Insert the workpiece support 1 into the table extension 3.
– Tighten the locking knob 2 to lock the workpiece support.
– Repeat the worksteps with the second workpiece support.
Preparing the Saw Stand
Preparing the Attachment Sets (see figures C1–C4)
– To release the attachment sets 5, press buttons 12 each
and open the levers 13.
– Measure the distance x between the mounting holes and
your power tool.
– Position the attachment sets 5 centred on the saw stand
and at the matching clearance x to each other.
– Lock the levers 13 again. The attachment sets are now
firmly positioned on the saw stand.
1 609 92A 2P5 | (14.11.16)
Fastening the Power Tool to the Attachment Sets
(see figure D)
– Position the power tool in the transport position.
Notes on the transport position are given in the operating
instructions of the respective power tool.
– Position the movable nuts 14 in the attachment sets so
that they match the mounting holes of the power tool.
– Screw the attachment set and the power tool with the hex-
agon bolts and the washers from the fastening kit 15 using
the provided open-end spanner 10.
Quantity
1
Operation
2
2
Working Advice
1
Do not overload the saw stand. Always observe the maximum
carrying capacity of the saw stand and the two table exten-
sions.
4
Always hold the workpiece firmly, especially the longer and
4
more heavy section. After cutting through the workpiece, the
centre of gravity may become dislocated in such an unfavour-
able manner that the saw stand tips over.
Extending the Saw Stand (see figures E1
Long workpieces must be underlaid or supported at their free
end.
– Place your long workpiece onto the saw table of the power
tool.
– Loosen locking knob 7 and pull the table extension 3 out to
the desired clearance.
– Retighten the locking knobs again.
– Loosen locking knob 2 and adjust the height of the work-
piece support 1 so that the workpiece rests level.
– Retighten the locking knobs again.
Sawing Workpieces of the Same Length
(see figure F)
The material stop 4 can be used for easily sawing workpieces
to the same length.
– Tilt the material stop 4 upward.
– Position the workpiece support 1 at the desired clearance
to the saw blade of the power tool.

Maintenance and Service

Maintenance and Cleaning

If the saw stand should fail despite the care taken in manufac-
ture and testing, repair should be carried out by an authorised
customer services agent for Bosch power tools.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the saw stand.
Accessories
Attachment set
Workpiece support
E2)
–
Article number
2 610 948 662
1 619 PA2 498
Bosch Power Tools