Wireless Microphones; Conformity And Approval; Before Operation; Setting Up The Active Speaker System - Monacor TXA-622CD/SW Mode D'emploi

Masquer les pouces Voir aussi pour TXA-622CD/SW:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

system is connected to the mains . Thus, the unit is
ideally suited for mobile applications .
The jacks LINK LINE (22) can be used to inter-
connect multiple active speaker systems for sound
applications in large zones . A passive 4 Ω speaker
system can also be operated in parallel (e . g . the
model TXB-602 / SW with a matching design) .

3.1 Wireless microphones

The following wireless microphones are available
from MONACOR:
Type
Hand-held wireless microphone
Pocket transmitter for
headband microphones
Pocket transmitter with
tie clip microphone
Pocket transmitter with
headband microphone

3.2 Conformity and approval

Herewith, MONACOR INTERNATIONAL declare that
the active speaker system TXA-622CD / SW com-
plies with the directive 2014 / 53 / EU . The EU dec-
laration of conformity is available on the Internet:
www .monacor .com
The active speaker system and the correspond-
ing wireless microphone are generally approved
for operation in EU and EFTA countries; they are
licence-free and requires no registration.

4 Before Operation

4.1 Setting up the active speaker system

Place the active speaker system as desired or mount
it onto a PA speaker stand (e . g . PAST series from
MONACOR) via the stand sleeve on its lower side .
The unit can be operated inside its transport
bag: Unzip the zip fasteners of the flaps covering
the speakers, the connections and the operating
elements . Fold up the flaps and secure them with
hook-and-loop fasteners .
12
Model
TXS-821HT
×
TXS-822HT
×
TXS-820HSE
×
TXS-822HSE
×
TXS-820LT
×
TXS-822LT
×
TXS-820SX
×
TXS-822SX
×

4.2 Power supply

The speaker system is supplied with power via the
integrated battery which is charged via the internal
charger .
1) For charging the battery, connect the mains
cable provided to the mains jack (32) and con-
nect the mains plug to a socket (230 V/ 50 Hz) .
2) The LED CHARGE (20) lights up:
red = the battery is being charged
green = the charging process has been com-
pleted
The unit may be operated while its battery is
charged; however, as long as the red LED LOW
lights up, the full power is not available . To re-
duce the charging time, switch off the unit with
the POWER switch (28) .
3) When the battery has been fully charged, the
LED CHARGE lights up in green . At maximum
volume, a mains-independent operating time of
up to 10 hours will be possible . A lower volume
will extend the operating time .
4) Recharge the battery when the red LED LOW
lights up .
Important!
Always disconnect the mains plug from the
socket when the battery has been fully charged
(LED CHARGE lights up in green) and the unit
is not operated; otherwise, the battery may be
damaged .

4.3 Connecting the active speaker system

Unit
Microphone with XLR plug
Audio units with line output,
e. g.: mixer, MP3 / CD player,
radio, microphone pre-
amplifier
Active speaker system
Passive speaker system
Connection to jack
MIC / LINE (16)
LINE IN (21) and
with 6.3 mm plug to
MIC / LINE (16) if no micro-
phone is connected
LINE LINK (22)
If a second speaker system
TXA-622CD / SW or
TXA-602 / SW is used,
connect its input LINE IN to
the output LINE LINK of the
first speaker system.
EXTERNAL SPEAKER (30)

Publicité

Table des Matières
loading

Table des Matières