TOPRO TROJA CLASSIC Manuel D'utilisation page 9

EN
Important to know about safety before use
•
Take care when folding and unfolding, do not trap your fingers.
•
Be aware not to put your fingers in open holes or between stationary parts.
•
Check the brakes every time before use and that the rollator locks into position when opened.
•
Not to be used by persons heavier than the maximum user weight (see table above).
•
Do not use to transport heavy loads or persons.
•
The rollator is not a toy and therefore should be treated in an appropriate manner.
•
Make sure that the lock wheel for height adjustment for the handles is locked tightly.
•
Be aware that some parts of the rollator might feel hot or cold when exposed to extreme temperatures.
•
A training by a skilled person is advised, to get to know the device and learn how to use it correctly.
•
Do not alter the product as this might put your safety at risk and the guarantee will be void.
Important to know about safety when in use
•
When stationary or parked, always use the parking brakes on both sides A
•
Before sitting on the seat, make sure the parking brakes on both sides are in the locked position A
•
Do not lean or bend sideways or over the back of the rollator whilst in the seated position. Do not tilt the rollator
more than max. 5° sideways, to avoid risk of falling. Due to the same reason bags etc. must never be hung on the
handlebars.
•
The driving brakes can be held in a little B to reduce speed, but must not be in locked position when the rollator
is in motion.
•
To give the right support and safety, make sure the rollator is kept as close to your body as possible C
•
Walk straight, look forward and hold your backside in D. That is the easiest way to keep your balance.
•
Do not push the rollator too far from your body as this can cause unnecessary strain and you could fall.
•
Be aware that the rollator may roll faster than you walking downhill, which may put you in risk of falling.
•
Do not use the rollator on stairs. Be careful when descending kerbs.
•
Be careful when wearing flared skirts and trousers as they could be caught between the brake block and wheel,
which could lead to falling. We therefore recommend not wearing flared/wide clothing.
•
For safety reasons it is prohibited to sit on the rollator during public transportation. Place your rollator securely and
use the parking brake.
Assembling / adjusting
TOPRO TROJA is delivered assembled. Before use, you must unfold the rollator. The height of the handlebar tubes will
then need adjusting to suit the user's needs. Please read the following paragraphs carefully.
Unfolding / folding
Unfolding: Release the lock clamp positioned at the seat bars A. Press the seat bars down and out B. The side frames
will slide apart. Press down the seat bars. You will hear a clicking sound. The rollator is now locked in its open position.
Folding: Pull the strap on the seat C and press the side frames together. Lock the clamp D over the seat bars.
Lowering and height adjusting of the handles
Lowering: Unscrew the lock wheel A (approx. 4–5 turns). Push the handlebar tubes down until they stop B. Tighten
the lock wheel A again.
Height adjusting: Unscrew the lock wheel A for the brake handles A (approx. 4–5 turns). Adjust the handlebar tubes
to a suitable height then pull them slightly up and down C until you hear a clicking sound. Tighten the lock wheel A
again. Adjust both handlebars to the same height. It is recommended that the handlebars are set to the same height as
your wrists when your arms are hanging alongside your body.
Height adjustment using the memory function
You have the opportunity to set the height of the handles at a standard setting fitted to your requirements so that
you easily can find the same height again. This can be necessary when the rollator is being transported or stored as
compact as possible. Decide on the height of the handlebars. Count visible holes at the back of the handlebar tubes.
Unscrew the lock wheel A. Pull the tube B out of the frame. The fastening piece C will now follow the handlebar tube.
Move the fastening piece C on the tube B so the number of holes corresponds to the number counted earlier. Fit the
memory chip D on the handlebar tube in the first available hole under the fastening piece C. Push the handlebar tube
B down and into the side frame E until the fastening piece is locked. Screw the lock wheel A half in. Pull the handle-
bars F up until they stop and then tighten the lock wheel A properly. From now on, when the handlebars are in the
lowest position, they will stop in the preset position automatically when pulled up.
8
3
www.topro.no
TROJA CLASSIC
2
4
5
EN