Mitsubishi Electric CITY MULTI PKFY-P06 NAMU-E Manuel D'installation page 4

3. Installing the indoor unit
I PKFY-P12/P15NGMU-E
¡
£
∞
¶
Fig. 3-2
I PKFY-P18/P24/P30NFMU-E
¡
£
∞
¶
Fig. 3-3
I PKFY-P06/P08NAMU-E
3-1/8
( 79.5 )
17-23/32 ( 450 )
B
C
D
3-1/8 12-29/32
( 79.5 ) ( 328 )
I E F H
W
3-15/16 ( 100 )
B
5 10
X
Y
Z
Fig. 3-4
4
™
¢
§
™
¢
§
•
10-1/4 ( 260 )
7-15/32 ( 190 )
N
4-5/16
( 109.5 )
17-23/32 ( 450 )
A
M
L
11-23/32 4-5-16
( 298 ) ( 109.5 )
G J K
* The hole position on the left side is 5-1/8 in.
(130 mm) from scale slot department.
I PKFY-P12/P15NGMU-E (Fig. 3-2)
PARTNUMBER ACCESSORY
¡
Mount board
Tapping screw 4 × 35
™
£
Pipe cover
¢
Band
∞
Felt tape
§
Joint pipe
¶
Mount piece
I PKFY-P18/P24/P30NFMU-E (Fig. 3-3)
PARTNUMBER ACCESSORY
1 Wall-fixing bracket
Tapping screw 4 × 35
2
3 Pipe cover
4 Band
5 Felt tape
6 Drain socket
7 Joint pipe
8 Flare nut
3.2. Installing the mount board
in.(mm)
1) Setting the mount board and piping positions
s Using the mount board, determine the unit's installation position and the
locations of the piping holes to be drilled.
Warning:
Before drilling a hole in the wall, you must consult the building contractor.
I PKFY-P06/P08NAMU-E (Fig. 3-4)
A Supporting piece
B Mount board ¡
C Contour of the unit
D Slot (4P-3/16" × 1-3/8" (4-4.5 × 35 mm))
E Hole (8P-5/32" dia. (8-ø4.3 mm))
F Level setting standard
G Knockout hole
H Hole (12P-1/8" dia. (12-ø2.8 mm))
I Bolt hole (4P-11/32" dia. (4-ø9 mm))
J Screw hole (87P-3/16" dia. (87-ø5.1 mm))
K Piping hole (2-9/16" to 2-3/4" dia. (ø65-ø70 mm))
L Slot (4P-3/16" × 1-9/16" (4-4.5 × 40 mm))
M Slot (4P-3/16" × 1-15/32" (4-4.5 × 37 mm))
N Slot (4P-7/16" × 25/32" (4-11 × 20 mm))
W: Location for wall holes
X Insert scale.
Y Hole centre
Z Align the scale with the line.
QUANTITY LOCATION OF SETTING
1 Fix at the back of the unit
12
1
5 Set inside the unit
3
1
1 Set in packing
QUANTITY LOCATION OF SETTING
1 Fix at the back of the unit
12
2
4 (large) + 5 (small)
3
Set inside the unit
1
1
2 <ø3/8" (9.52),
P18
ø5/8" (15.88)>