Substantial Modifications To The Joystick Default Settings; Modifications To The Lookup Chart To Define Alias Keys - Videotec DCZ Manuel D'instructions

9.7.2.3 Substantial modifications to the
joystick default settings
Example: If you want to use just 8 joystick keys on
the left side of the keyboard.
OPERATION / COMMAND
Enter the programming settings
Select 5 .
Disconnect and reconnect the
keyboard.
Enter the programming settings again
4
Select .
Disconnect and reconnect the
keyboard.
[BlockModeStart]
Command.
[LookupWrite31,60001]
Command.
[LookupWrite32,60002]
Command.
[LookupWrite41,60003]
Command.
[LookupWrite42,60004]
Command.
[LookupWrite51,60005]
Command.
[LookupWrite52,60006]
Command.
[LookupWrite61,60007]
Command.
[LookupWrite62,60008]
Command.
[BlockModeEnd]
Command.
Enter the programming settings
Select 8 .
Disconnect and reconnect the
keyboard.
Check that the corresponding
LEDs come on when the keys
are pressed.
Tab. 07
18
EFFECT
Resets the JOYHID key
chart to default settings.
It restarts in JOYHID mode.
It switches to VCOM mode
resetting the lookup chart
(no keys valid for the
joystick).
It restarts in VCOM mode.
This allows you to
modify the internal
memory without using
it for multiple writing
commands.
Creates key 1 on row 3,
column 1.
Creates key 2 on row 3,
column 2.
Creates key 3 on row 4,
column 1.
Creates key 4 on row 4,
column 2.
Creates key 5 on row 5,
column 1.
Creates key 5 on row 5,
column 2.
Creates key 7 on row 6,
column 1.
Creates key 8 on row 6,
column 2.
Saves the modifications to
the internal memory.
Switches to JOYHID mode
without resetting the
lookup chart that has just
been modified.
It restarts in JOYHID mode.
9.7.3 Modifications to the lookup chart
to define alias keys
It is possible to have several keys that all perform the
same commands (e.g. the shift keys). If a series of
alias keys are pressed together at the same time, the
pressed key event ([K+xx]) is only transmitted the
first time it is pressed; the released key event ([K-
xx]) is only transmitted when all the keys with the
same alias have also been released.
Example: The 5 bottom keys on the keyboard act as if
they are the same key.
OPERATION / COMMAND
Enter the programming settings
4
Select .
Disconnect and reconnect the
keyboard.
[BlockModeStart]
Command.
[LookupWrite84,50083]
Command.
[LookupWrite85,50083]
Command.
[LookupWrite86,50083]
Command.
[LookupWrite87,50083]
Command.
[BlockModeEnd]
Command.
Enter the programming settings
Check that when the 5 lower
keys are pressed, they all
transmit the same message
[K+83].
Tab. 08
EFFECT
Switches to VCOM mode
resetting the lookup chart.
It restarts in VCOM mode.
This allows you to
modify the internal
memory without using
it for multiple writing
commands.
The key on row 8, column
4, is an alias of the key on
row 8, column 3.
The key on row 8, column
5, is an alias of the key on
row 8, column 3.
The key on row 8, column
6, is an alias of the key on
row 8, column 3.
The key on row 8, column
7, is an alias of the key on
row 8, column 3.
Saves the modifications to
the internal memory.