JB Systems Mini LED MANAGER Mode D'emploi page 6

ENGLISH
starting address of each individual unit, this will be done for you!
 Make sure that ALL DIP-switches are set to OFF position!
 Make sure the DMX cables of all units are connected.
 Connect the first unit to a universal DMX controller.
 Connect all units to the mains so they are switched on.
 Set all DMX-channels on your DMX-controller to zero (value 000).
 Set the DMX-channel, that you want to assign as DMX-start address on your mini LED Manager,
to maximum (value 255)
 Press the "Auto DMX address" button (6) on the first mini LED Manager in the chain for about
5seconds.
 Done!  The first mini LED Manager in the chain will receive the DMX-start address you chose
and it will automatically calculate and program the DMX addresses of all the other units in the
DMX-chain!
An example to make things clear:
We want to set the DMX-addresses of 16 units, the DMX start address of the first mini LED
Manager must be 202:
 Connect all mini LED Manager to the DMX-controller as described above and make sure all are
switched on.
 Set all DMX-channels on the controller to zero (000)
 Now set DMX-channel 202 to maximum (255)
 Press the "Auto DMX address" button (6) on the first mini LED Manager in the chain for about
5seconds.
 Done!  The first mini LED Manager in the chain will receive DMX-start address 202 and it will
automatically calculate and program the DMX addresses of all the other units in the DMX-chain!
nd
This means that the 2 mini LED Manager automatically receives address 206, the 3
th
address 210, ..., until the 16 mini LED Manager who automatically receives start address 262.
You just programmed 16 mini LED Manager, this took you about 10seconds!!!
Remark: you can mix the units with other DMX-effects that don't have the automatic DMX-
addressing option. In that case you still have to set the DMX-addresses of these DMX-effects
manually! You can also mix the Mini LED Managers with other JB Systems LED products that have
the auto DMX-feature. They will also automatically receive their DMX-addresses.
OPERATING INSTRUCTIONS
A. Standalone 1unit:
 Connect the LED projectors to the Mini Led Manager as indicated in the previous chapters.
 Switch the unit on and refer to the chapter "DIP SWITCH SETTINGS" to make yourself familiar with
the various functions of the faders and buttons.
B. Two or more units in master/slave setup:
 Connect the LED projectors to the Mini Led Managers as indicated in the previous chapters.
 Connect the units with each other as explained in the chapter about electrical installations.
 Switch the Mini Led Managers on. You can only use the controls on the master unit, the controls on
the slaves are disabled. Refer to the chapter "DIP SWITCH SETTINGS" to make yourself familiar with
the various functions of the faders and buttons on the master unit.
C. Connect the optional LEDCON-02 (or LEDCON-01) for remote control:
In most cases the MINI LED MANAGER will be installed on a wall, close to the LED-projectors. If you
want to have easy access to its functions, you can connect the LEDCON-02 (or LEDCON-01) remote
controller to the (first) Mini Led Manager. The other connections are identical to those of the standalone
or master/slave setups. Don't forget to perform the automatic addressing on the LEDCON-02!!!
D. Controlled by universal DMX-controller:
 Connect the LED projectors to the Mini Led Manager(s) as indicated in the previous chapters.
 Connect the Mini Led Manager(s) with all other DMX-appliances in the DMX-chain.
 Switch all units on and set the proper DMX-addresses. (don't forget to set DIP-switch 10 to OFF)
 Switch your universal DMX-controller on and refer to the DMX chart below to control the connected
Mini Led Managers:
JB SYSTEMS®
OPERATION MANUAL
7/51 MINI LED MANAGER
ENGLISH
SPECIFICATIONS
rd
has
Power Input:
Fuse:
Output voltage to LEDs:
Output power to LEDs:
DMX connections:
DMX channels:
Audio input:
Size:
Weight:
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS®
AC 230V~ 50Hz
3,15A / 250V slow blow (20mm glass)
DC 24V common anode
1x 100W max
Red: 33W max.
o
o Green: 33W max.
Blue: 33W max.
o
3pin XLR (DMX-512 standard)
4 (CH1: red, CH2: green, CH3:blue, CH4:dimmer/strobe)
None, internal microphone
255 ×110×88 mm
1,82kg
Every information is subject to change without prior notice
8/51
OPERATION MANUAL
MINI LED MANAGER