Page 1
N ÁV OD K OBS L UZE A I NS TA L A CI G HID D E INS TALARE S I UTI LI ZAR E VT 70/04 E, VT 70/08 E, VT 70/40 E, VT 70/80 E 1 0 1 5 - 2 2...
Page 2
CONTENT Declaration of a standards conformity Instruction for use Cleaning and maintenance INHALT Die Normenübereinstimmungsdeklaration Gebrauchsanweisung Die Reinigung und instandshaltung CONTENU Déclaration de conformité Mode d‘emploi Nettoyage et entretien INHOUD De verklaring van overeenstemming met de normen Gebruiksaanwijzing Reiniging en onderhoud OBSAH Prohlášení...
Page 3
DECLARATION OF A STANDARDS CONFORMITY The producer confi rms that the devices agree with 2014/30/EU, 2014/35/EU standards, rule nr. 117/2016 sb., 118/2016 sb. and with relevant goverment orders. Instalation must be done with respect to valid standards. Attention, the producer refuses any responsibility in case of direct or indirect damages which are caused due to wrong instalation, incorrect intervention or modifi...
Page 4
PLACEMENT The device must be instalated in well ventilated room what is necessary for regulation of the function of the device (technician must go by valid standard (EN..). If the device is situated close to the wall or if it is in contact with the furniture walls, these walls must resist the temperatures ranging to 90°C.
Page 5
SAFETY MEASURES FROM STANDPOINT FIRE PROTECTION ACCORDING TO EN 061008 ČL. 21 • only adults can operate the device • device must be safely used in common surroundings according to EN 332000-4-462; EN 332000-4-42. You must switch the gas device off under the circumstances leading: to the danger of the temporary rise of the combustion gas or steam or during works when there is a big possibilityof rise ot the temporary fi...
Page 6
INSTRUCTION FOR USE Before the fi rst use of the device you must remove protection foil from all surfaces and wash the device with moist cleaning cloth dipped in the water with detergent. Than dry it with cloth. The bath is fi lled with water through the supply valve, which is located on the front panel. The bath must be fi...
Page 7
CLEANING AND MAINTENANCE It is recommended to have the device checked by the professional service min. once a year. All interventions must be done by qualifi ed person who is competent for this. ATTENTION! The device cannot be cleaned by direct or pressure water. Clean it daily. Daily maintenance keeps longer useful life and effi...
Page 8
DIE NORMENÜBEREINSTIMMUNGSDEKLARATION Der Produzent erklärt, daß die Geräte in einer Übereinstimmung mit den Vorschriften der 2014/35/EU, 2014/30/ EU dem Gesetz Nr. 118/2016 sb., 117/2016 sb. der Sammlung und zugehörigen Regierungsverordnungen stehen. Die Installation muss mit der Absicht auf geltende Normen durchgeführt werden. Vorsicht, im Falle einer direkten oder indirekten Beschädigung, die sich auf falsche Installation, unrichtigen Eingriff oder Anpassungen, ungenügende Instandshaltung, unrichtige Verwendung beziehen, und welche eventuell durch andere Ursachen, als in Punkten der Verkaufsbedingungen angeführt ist, so verzichtet der Importeur auf...
Page 9
DIE VERPACKUNGS-, UND VORRICHTUNGSKONTROLLE Die Vorrichtung verlässt unsere Lager in ordentlicher Verpackung, auf deren die entsprechenden Symbole und Bezeichnungen stehen. In der Verpackung befi ndet sich entsprechende Bedienungsanweisung. Falls die Verpackung eine schlechte Behandlung oder Anzeichen der Beschädigungen vorweist, muß dieses sofort beim Transporteur reklamiert werden und zwar durch Unterzeichnung eines Schadensprotokolles.
Page 10
DIE PLATZIERUNG Es ist unbedingt notwendig, zu der Regulation der Gerätetätigkeit, daß das Milieu - der Küche -, wo das Gerät installiert wird, sehr gut belüftbar ist (im Hinblick darauf: sei der Techniker sich mit geltenden Normen (EN) richtet). Wenn die Einrichtung so plaziert wird, daß sie im Mobiliarwandkontakt stehen wird, so müssen diese einer Temperatur von 90°C wiederstehen.
Page 11
DIE SICHERHEITSVORRICHTUNGEN AUS DER SICHT DES FEUERSCHUTZES LAUT EN. 061008 ČL. 21 Die Einrichtungsbedienung dürfen nur Erwachsene ausführen • Das Gerät darf sicher in gewöhnlicher Umgebung laut EN 332000-4-482; EN 332000-4-42 verwendet werden. • Es ist notwendig das Gerät so platzieren, daß es auf einer unbrennbaren Grundlage steht oder hängt. •...
Page 12
GEBRAUCHSANWEISUNG Vorsicht! Bevor Sie das Gerät verwenden werden, ist es notwendig ihn gut mit feuchtem Lappen abzuwaschen. Lassen Sie nie das Gerät ohne Aufsicht im Betrieb. Das Wasser wird mittels des Einlassventils eingelassen, das sich an der vorderen Platte befi ndet. Das erste Einlassen ist allmählich durchzuführen, da sich im Wassersystem Luft befi...
Page 13
DIE REINIGUNG UND INSTANDSHALTUNG ACHTUNG! Die Einrichtung darf nicht mit Direkt-, oder Druckwasserstrahl gereinigt werden. Reinigen Sie das Gerät täglich. Die Lebensdauer und Gerätewirkung wird durch die tägliche Wartung gewährleistet. Überzeugen Sie sich, vorm Reinigungsanfang, dass Sie die Einrichtung vom Elektrostrom abgeschaltet haben. Schalten Sie immer die Gerätehauptzufuhr ab.
Page 14
DÉCLARATION DE CONFORMITÉ 2014/30/EU, 2014/35/EU Le fabricant certifi e la conformité des appareils aux normes à la loi n° 117/2016 sb., 17/2003 sb. et aux décrets applicables. L‘installation doit être effectuée dans le respect des normes en vigueur. Attention: le fabricant décline toute responsabilité en cas de dommages, directs ou indirects, causés par une mauvaise installation, par une utilisation, des interventions ou des modifi...
Page 15
LA LOCATION Le local dans lequel l‘appareil est installé doit être bien ventilé. Si l’appareil doit toucher le parois , celui-ci doit résister à la chaleur de 90°C au minimum. L’installation, le réglage et la mise en marche doivent être effectués par une personne qualifi...
Page 16
MÉSURES DE SÉCURITÉ POUR LA PROTECTION CONTRE INCENDIE SELON EN 06 1008 ARTICLE 21: - l’apparel ne peut être utilisé que par des personnes majeures - l’appareil peut être utilisé dans un espace ordinaire selon EN 332000-4-482; 332000-4-42 - l’appareil doit être placé ou suspendu d’une manière stable sur une surface ininfl ammable Il est interdit de placer sur l’appareil ou dans la distance inférieure à...
Page 17
MODE D’EMPLOI Attention ! Avant la première utilisation, il faut laver l’appareil à l’aide d’un torchon humide et d’un détergent. Rincer et sécher. La vanne d’arrivée d’eau est située sur le panneau avant. Il faut remplir le bain-marie avec précaution, en raison de la présence de bulles d’air dans la tuyauterie, qui risqueraient de provoquer une brusque arrivée d’eau au niveau du bec de robinet.
Page 18
NETTOYAGE ET ENTRETIEN Il est recommandé de faire controller l’appareil dans un service spécialisé au moins une fois par an. Toutes les interventions peuvent être effectuées seulement par une personne qualifi ée ayante une autorisation pour ces interventions. ATTENTION ! L’appareil ne peut pas être nettoyé sous l’eau courante ou de pression. Nettoyer l’appareil chaque jour.
Page 19
DE VERKLARING VAN OVEREENSTEMMING MET DE NORMEN De fabrikant verklaart dat de apparaten voldoen aan de basiseisen van de richtlijn 2014/30/EU (verordening van de regering nr. 117/2016 Coll.) en de eisen van de richtlijn 2014/35/EU (verordening van de regering nr. 118/2016 Coll.).
Page 20
Controle van de verpakking en het apparaat Het apparaat verlaat ons magazijn in een verpakking die voldoet aan alle voorschrift en en waarop zich de vereiste symbolen en markeringen bevinden. In de verpakking bevindt zich de overeenkomstige gebruik- saanwijzing. Indien de verpakking beschadigd is of wijst op onjuist transport, dient u dit onmiddellijk te reclameren bij de transporteur door middel van ondertekening van een schadeprotocol.
Page 21
Plaatsing De volgende richtlijnen in overeenstemming met de normen TPG G 704 01, ČSN 127040 en ČSN 127010 moeten in acht worden genomen voor de juiste werking en opstelling van het apparaat. Pak het apparaat uit een controleer of het tijdens het transport niet is beschadigd. Plaats het apparaat op een horizontale oppervlakte (de maximale oneff...
Page 22
Veiligheidsvoorzieningen in verband met brandpreventie conform ČSN 061008 art. 21 • het apparaat mag uitsluitend door volwassenen bediend worden • het apparaat kan veilig gebruikt worden in overeenstemming van de volgende normen: ČSN 33 2000-4-482: Brandbeveiliging in gebieden met een speciaal risico of gevaar ČSN 33 2000-4-42: Bescherming tegen invloeden van warmte •...
Page 23
Aansluiting van de elektrische kabel op het elektriciteitsnet De aansluiting op het elektriciteitsnet - de voedingskabel moet zelfstandig beveiligd worden. Namelijk door de toepassing van een zekering voor nominale stroom, afhankelijk van het aansluitvermogen van het geïnstalleerde apparaat. Controleer het aansluitvermogen van het apparaat op het typeplaatje dat zich op het achterpaneel (of zijkant) van het apparaat bevindt.
Page 24
GEBRUIKSAANWIJZING Opgelet! Voordat u het apparaat gebruikt, moet u de beschermende folie van het gehele oppervlak verwijderen, het vervolgens goed met water en afwasmiddel wassen en daarna met een vochtige doek afnemen. Water wordt gevuld met behulp van de waterventiel die zich op het voorste paneel bevindt. De eerste vulling moet langzaam uitgevoerd worden omdat het watersysteem belucht wordt en er water uit de vularm kan spatten.
Page 25
REINIGING EN ONDERHOUD Het apparaat moet ten minste 2x per jaar door een gespecialiseerde service gecontroleerd worden. Alle ingrepen aan het apparaat mogen slechts door een gekwalificeerd persoon worden uitgevoerd, die da- artoe bevoegd is. OPGELET! Het apparaat mag niet schoongemaakt worden met een directe waterstraal of met een ho- gedrukreiniger.
Page 31
VT-70/80 E ENGLISH DEUTSCH FRANÇAIS TERMINAL TERMINAL TERMINAL SWITCH O / I SWITCH O / I INTERRUPTEUR O / I ILLUMINATED SWITCH O / I BELEUCHTETE SWITCH O / I INTERRUPTEUR ILLUMINÉ O / I ROTARY SWITCH SWITCH ROTARY SWITCH ROTARY PUSH BUTTON SWITCHES DRUCKSCHALTER BOUTON POUSSOIR...
Page 32
PROHLÁŠENÍ O SOULADU S NORMAMI Výrobce prohlašuje, že přístroje splňují základní požadavky směrnice 2014/30/EU (nařízení vlády č. 117/2016 Sb.) a požadavky směrnice 2014/35/EU (nařízení vlády č. 118/2016 Sb.). Pozor, výrobce se vzdává jakékoli odpovědnosti v případě přímých i nepřímých poškození, které se vztahují...
Page 33
KONTROLA OBALU A ZAŘÍZENÍ Zařízení opouští naše sklady v řádném obalu, na kterém jsou odpovídající symboly a označení. V obalu se nachází odpovídající návod k obsluze. Jestliže by obal měl vykazovat špatné zacházení, známky poškození, musí se okamžitě reklamovat u přepravce a to sepsáním a podepsáním protokolu o škodě. Na pozdější reklamace nebude brán zřetel.
Page 34
BEZPEČNOSTNÍ OPATŘENÍ Z HLEDISKA POŽÁRNÍ OCHRANY PODLE ČSN 061008 ČL. 21 • obsluhu spotřebiče smí provádět pouze dospělé osoby • spotřebič smí být bezpečně používán v souladu s normami a zákony dané země. • spotřebič je nutné umístit tak, aby stál nebo visel pevně na nehořlavém podkladu Na spotřebič...
Page 35
PŘIPOJENÍ ELEKTRICKÉHO KABELU DO SÍTĚ Instalace elektrického přívodu - tento přívod musí být samostatně jištěn. A to odpovídajícím jističem jmenovitého proudu v závislosti na příkonu instalovaného přístroje. Příkon přístroje zkontrolujte na výrobním štítku na zadním panelu (či boku) přístroje. Připojený zemnící vodič musí být delší než ostatní vodiče. Přístroj připojte přímo na síť, je nezbytné vložit mezi spotřebič...
Page 36
NÁVOD K POUŽITÍ Pozor! Než-li začnete přístroj používat, je nutné z celého povrchu sejmout ochranné fólie, a pak jej dobře omýt vodou se saponátem na nádobí, a poté otřít vlhkým hadrem. Voda se napouští pomocí napouštěcího ventilu, který je umístěn na předním panelu. První napouštění...
Page 38
ČIŠTENÍ A ÚDRŽBA POZOR! Zařízení se nesmí čistit přímou nebo tlakovou vodou. Čistěte zařízení denně, odpojené od energie a vychladlé. Denní údržba prodlužuje životnost a účinnost zařízení. Před započetím čistění se přesvědčte, jestli jste odpojili zařízení od elektrického proudu. Vždy vypněte hlavní přívod k zařízení.
Page 39
ROZMĚROVÝ OBRÁZEK VT VT-70/04 E VT-70/08 E...
Page 45
TENSIUNE PUTERE DIMENSIUNE (V/Hz) (kW) (mm) VT 70/04 E 400 / 50 400 x 737 x 331 VT 70/08 E 400 / 50 2x 4,5 800 x 737 x 331 VT 70/40 E...
Page 46
VERIFICAREA AMBALAJULUI ŞI APARATULUI Aparatul iese din depozitele noastre ambalat în mod regulameentar, cu indicarea simbolurilor şi însemnelor corespunzătoare. Ghidul de deservire corespunzător se găseşte în ambalaj. Dacă ambalajul prezintă semne de manevrare necorespunzătoare sau urme de deteriorare, este necesar de atenţionat transportatorul şi de a face un proces verbal de deteriorare.
Page 47
INSTALAREA Instrucţiuni tehnice pentru instalare şi reglare Destinat DOAR utilizării de către tehnicieni specializaţi. Instrucţiunile următoare sunt destinate tehnicianului califi cat pentru reparaţie: Toate operaţiunile trebuie sa fi e efectuate cât mai atent şi în conformitate cu normele actuale!!! Important: Orice activitate de reglare a aparatului trebuie efectuată...
Page 48
CONECTAREA CABLULUI ELECTRIC LA REŢEA CONECTAREA CABLULUI ELECTRIC LA REŢEA Instalarea alimentării cu electricitate: conexiunea trebuie asigurată de sine stătătoare cu o siguranţă corespunzătoare şi în funcţie de tensiunea aparatului instalat. Tensiunea aparatului poate fi verifi cată pe plăcuţa producătorului din partea din spate a aparatului. Conectaţi aparatul direct la reţea şi plasaţi un întrerupător între aparat şi reţea, respectând distanţa minimă...
Page 49
GHID DE UTILIZARE Atenţiune! Înainte de prima utilizare a dispozitivului, trebuie să îndepărtați folia de protecție de pe toate suprafețele și să spălați dispozitivul cu o cârpă de curățare umedă cufundată în apă cu detergent. Decât să o usuci cu o cârpă.
Page 50
CURĂŢARE ŞI ÎNTREŢINERE CURĂŢARE ŞI ÎNTREŢINERE Este recomandat de a inspecta aparatul, cel puţin o dată pe an, de către un servis specializat. Orice intervenţii asupra aparatului pot fi operate doar de către o persoană califi cată, autorizată în acest sens.
Page 51
DIMENSIUNILOR IMAGINE VT 70/04 E VT 70/08 E...
Page 56
SCHEMA CONECTRII: VT 70/80 E 1 - terminale 4 - comutator 5 - comutator cu buton 8 - contactor 9 - contacte contactor 11 - termostat de lucru 12 - termostat de siguranță 13 - indicator luminos alb 14 - indicator luminos verde 17 - element de încălzire...
Page 57
List of service organizations: CZ: RM GASTRO CZ s. r. o., Náchodská 818/16, Praha 9 Tel. +420 281 926 604, info@rmgastro.cz, www.rmgastro.cz SK: RM Gastro Slovakia, Rybárska 1, Nové Město nad Váhom Tel.: +421 32 7717061, obchod@rmgastro.sk, www.rmgastro.sk PL: RM GASTRO Polska Sp. z o. o., ul. Skoczowska 94, 43-450 Ustroń Tel.: +33 854 73 26, www.rmgastro.pl...