Stomer Professional SAD-14Bx2-LiD Mode D'emploi page 7

Cordless drill/driver
INTENDED USE
• This tool is intended for drilling in wood, metal, ceramic and
plastic; tools with electronic speed control and left/right ro-
tation are also suitable for screwdriving and thread cutting
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1 Switch for on/off and speed control
2 Switch for changing direction of rotation
3 Keyless chuck
4 Ring for torque control
SAFETY
WARNING! Read all instructions. Failure to follow all instruc-
tions listed below may result in electric shock, fi re and/or seri-
ous injury.
• Ensure the switch is in the off position before inserting bat-
tery pack. Inserting the battery pack into power tools that
have the switch on invites accidents.
• Recharge only with the charger specifi ed by the manufac-
turer. A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another battery
pack.
• Use power tools only with specifi cally designated battery
packs. Use of any other battery packs may create a risk of
injury and fi re.
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before you
start working
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger (charg-
ers with a rating of 230V or 240V can also be connected to
a 220V supply)
• In case of electrical or mechanical malfunction, immediate-
ly switch off the tool or unplug charger from power source
• SBM Group can assure fl awless functioning of the tool only
when original accessories are used
• Use only accessories with an allowable speed matching at
least the highest no-load speed of the tool
• This tool should not be used by people under the age of 16
years
• Be careful not to drill or drive into areas where electrical
wires may be contacted
• Ensure that switch (2) is in the middle (locking) position
before making any adjustments or changing accessories
as well as when carrying or storing the tool
• Do not touch the contacts in the charger
• Do not expose tool/charger/battery to rain
• Never charge battery outdoors
• Store tool/charger/battery in locations where temperature
will not exceed 40° C or drop below 0° C
• Batteries will explode in fi re, so do not burn battery for any
reason
• When damaged, and under extreme usage and tempera-
ture conditions, batteries may start to leak
1
2
- if liquid comes into contact with the skin, wash quickly with
soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, fl ush eyes with clean water for
a minimum of 10 minutes and seek immediately medical
attention
• When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc. to
prevent short-circuit
• Do not use charger when damaged; take it to one of the of-
fi cially registered SBM Group Service Stations for a safety
check
• Do not use battery when damaged; it should be replaced
immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable batteries with
the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire in
the cord of the charger to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of the charg-
er, it must be disposed of safely and not left unattended
To ensure longer service life and proper perform-
ance of the battery, take the following actions when
you start using new battery:
1. Use the new battery, without recharging it, till its complete
discharge.
2. Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to
reach the nominal battery capacity.
MAINTENANCE
Make sure that the machine is not live when carry-
ing out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth, prefer-
ably after each use. Keep the ventilation slots free from dust
and dirt.If the dirt does not come off use a soft cloth moistened
with soapy water. Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may damage the plastic
parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please contact
your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during transport,
it is delivered in a sturdy packaging. Most of the packaging
materials can be recycled. Take these materials to the appro-
priate recycling locations. Take your unwanted machines to
your local SBM Group dealer. Here they will be disposed of in
an environmentally safe way.
Li-Ion batteries can be recycled. Deliver them to a disposal site for
chemical waste so that they can be recycled or disposed of in an
environmentally friendly manner.
7