Télécharger Imprimer la page

Homeright Finish Max C800766 Manuel D'instructions page 4

Publicité

Les langues disponibles

Les langues disponibles

WARNINGS
• DO NOT aim sprayer at yourself or anyone else; in the event of
injury, seek expert medical advice immediately.
• DO NOT cover the nozzle with any part of your body. High velocity
jet can cause accidental injuries.
• DO NOT leave your sprayer uncleaned or allow paint to dry in the
sprayer. An uncleaned sprayer will not work the next time it's
used and you could void the warranty.
• DO NOT spray textured materials containing asbestos fibers.
• DO NOT spray any textured materials containing particles or
fibers such as metallic paints or fire retardant paints.
• DO NOT spray flammable liquid. (Example: lacquer)
• DO NOT use the sprayer outside when it's raining.
• DO NOT use sprayer below garage floor or grade level.
• DO NOT disassemble the sprayer without reading directions.
• DO NOT allow any part of the body to come into contact with
the fluid stream.
• DO plug the cord or extension cord only into grounded power supply.
• DO keep the sprayer out of the reach of children.
• ALWAYS place the sprayer upright (do not place the sprayer
upside down or on its side) to prevent liquid from entering
internal wiring and causing electric shock.
• ALWAYS wear mask, goggles, and ear and eye protection while
operating the sprayer.
• When you stop spraying, ALWAYS unplug the cord to prevent
unintended operation.
• To prevent electrical shock, NEVER immerse the sprayer into
water or other liquids.
• NEVER leave sprayer unattended.
• NEVER leave sprayer plugged in while cleaning.
SERVICING A DOUBLE-INSULATED PRODUCT
In a double-insulated product, two systems of insulation are
provided instead of grounding. No grounding means are provided
on a double insulated product, nor should a means of grounding
be added to the product. Servicing of a double-insulated product
requires extreme care and knowledge of the system and should
only be done by qualified service personnel.
Replacement parts for a double-insulated product must be identical
to those parts in the product.
IMPORTANT SAFEGUARDS
FINISH MAX
FINE FINISH SPRAYER
®
1. HAZARD: Solvent and paint fumes can explode or ignite, causing
property damage and severe injury. Avoid all low ignition sources
such as static electricity, sparks, and open flames.
2. HAZARD: Paints, solvents, insecticides, and other materials
may be harmful if inhaled, causing severe nausea, fainting,
or poisoning.
3. HAZARD: Do not hold cord at plug connections to support cord.
Failure to observe may result in electrical shock.
PROP 65
• WARNING:
This product can expose you to chemicals including Antimony
Trioxide, which is known to the State of California to cause cancer,
and Lead and Nickel, which are known to the State of California
to cause birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov.
HAZARD: EXPLOSION OR FIRE
Paint, stain, and solvent fumes can explode or ignite, causing
property damage and/or severe injury.
• Keep area well ventilated. Exhaust and introduce fresh air to keep
fumes from accumulating in work area.
• Do not spray in areas where there are ignition sources, static
electricity, sparks, pilot lights, heaters, hot objects, cigarettes,
or open flames.
• Have fire extinguishing equipment present and in good
working order.
• Follow safety instructions and IMPORTANT SAFEGUARDS of
material manufacturers.
HAZARD: HAZARDOUS VAPORS
Paint, stain and solvents, insecticides, varnishes, and other
materials may be harmful if inhaled, causing severe nausea,
fainting, or poisoning.
• Use a mask or respirator when spraying when there is a chance
of inhaling vapors.
• Use protective eyewear.
EXTENSION CORDS
Make sure your extension cord is UL/ETL/CSA listed and is in
good condition. When using an extension cord, be sure to use one
heavy enough for the current - for lengths less than 18 feet,
use a No. 18 AWG. or heavier; for lengths more than 18 feet,
use No. 16 AWG. If in doubt, use a heavier gauge. An undersized
cord will cause a drop in line voltage resulting in loss of power
and overheating.
STORAGE
Make sure unit is clean and dry before storing. Store in a dry
location. To prevent damage, the electrical cord should not be
crimped during storage .
(C800766, C900076)
3
CAUTION
ENGLISH

Publicité

loading

Ce manuel est également adapté pour:

Finish max c900076