EINHELL TE-RH 32-1600 4F Instructions D'origine page 15

5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Check the drilling point for concealed electrical
cables, gas and water pipes using a cable/pipe
detector.
5.1 Additional handle (Fig. 2 – Item 5)
For safety reasons you must only use the
hammer drill with the additional handle.
The additional handle (5) enables you to achieve
better stability whilst using the hammer drill. The
machine must not be used without the additional
handle (5) for safety reasons.
The additional handle (5) is secured to the
hammer drill by a clamp. Turning the handle anti-
clockwise (looking from the handle) will release
the clamp. Turning the handle clockwise will tigh-
ten the clamp.
First release the additional handle clamp. You can
then swing the additional handle (5) into the most
comfortable working position for you. Now turn
the additional handle in the opposite direction
again until the additional handle is secure.
5.2 Depth stop (Fig. 3 – Item 6)
The depth stop (6) is held in place with the lo-
cking screw (a) on the additional handle (5) by
means of a clamp.
•
Undo the locking screw (a) and fit the depth
stop (6).
•
Set the depth stop (6) to the same level as
the drill bit.
•
Pull the depth stop (6) back by the required
drilling depth.
•
Retighten the locking screw (a).
•
Now drill the hole until the depth stop (6) tou-
ches the workpiece.
5.3 Tool insertion (Fig. 4)
•
Clean the tool before insertion and apply a
thin coating of drill bit grease to the shaft of
the tool.
•
Insert the dust-free tool into the tool mounting
as far as it will go whilst turning it. The tool will
lock itself.
•
Check that it is properly secure by pulling the
tool.
Anl_TE_RH_32-1600_4F_SPK13.indb 15 Anl_TE_RH_32-1600_4F_SPK13.indb 15
GB
5.4 Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and re-
move the tool.
6. Operation
Danger
To prevent all danger, the machine must only be
held using the two handles (5/7). Otherwise there
may be a risk of suff ering an electric shock if you
drill into cables.
6.1 Switching On and Off (Fig. 1)
To switch on: Press and hold the operating switch
(4).
To switch off : Let go of the operating switch (4)
6.2 Drill / Hammer drill / Chisel selector
switch (Fig. 6)
•
For drilling, press the button (E) on the rotary
switch (3) and simultaneously turn the rotary
switch (3) to position A.
•
For hammer drilling, press the button (E) on
the rotary switch (3) and simultaneously turn
the rotary switch (3) to position B.
•
For chiseling, press the button (E) on the rota-
ry switch (3) and simultaneously turn the rota-
ry switch (3) to position C. In switch position C
the chisel is not locked.
•
For chiseling, press the button (E) on the
rotary switch (3) and simultaneously turn the
rotary switch (3) to position D. The chisel is
locked in position D.
Notice
Only low pressure is required for hammer drilling.
Excessive pressure will exert an unnecessary
force on the motor. Check the drill bits at regular
intervals. Sharpen or replace blunt drill bits.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by a special power cable
which is available from the manufacturer or its
after-sales service.
- 15 -
19.10.2022 13:01:35 19.10.2022 13:01:35