Makita DTP141RTJ Manuel D'instructions page 11

Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
NOTE:
• Choose suitable speed for the work load. Drilling over
the following capacity may damage the tool.
High speed
Low speed
012989
Screwdriver mode
CAUTION:
• Adjust the number on the LED display to the proper
torque level for your work.
• Make sure that the driver bit is inserted straight in the
screw head, or the screw and/or bit may be damaged.
• Hold the tool firmly. When the clutch cuts in or refasten-
ing, a sudden twisting force may occur and it can twist
your wrist.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually.
NOTE:
• This tool employs an electronic clutch. The tool stops
automatically when the clutch cuts in. To keep operat-
ing, release the switch trigger once.
• When driving wood screws, predrill pilot holes to make
driving easier and to prevent splitting of the workpiece.
See the chart.
Nominal diameter of wood
screw (mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
5.8
6.1
006421
NOTE:
• See the following chart for the relation between the
number of torque setting and fastening torque rate.
The fastening torque rate will be different depends on
materials. Make a test fastening to get the desired
torque before operation.
Drilling capacity
Steel 6.5 mm
Wood 12 mm
Steel 10 mm
Wood 21 mm
Recommended size of
pilot hole (mm)
2.0 – 2.2
2.2 – 2.5
2.5 – 2.8
2.9 – 3.2
3.1 – 3.4
3.3 – 3.6
3.7 – 3.9
4.0 – 4.2
4.2 – 4.4
Number Fastening torque rate
on LED
Low (1)
Display
Approx. 2.5 N•m
1
(Approx. 25.5 kgf. cm)
Approx. 4.6 N•m
3
(Approx. 46.9 kgf. cm)
Approx. 8.1 N•m
5
(Approx. 82.6 kgf. cm)
Approx. 10.0 N•m
7 (Approx. 102.0 kgf.
cm)
Approx. 11.5 N•m
9
(Approx. 117.3 kgf. cm)
012276
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance except for the following trou-
bleshooting related to the light.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Screw bits
• Hook
• Plastic carrying case
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN62841:
Model DTP131
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Model DTP141
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
High (2)
Approx. 1.1 N•m
(Approx. 11.2 kgf. cm)
Approx. 2.0 N•m
(Approx. 20.4 kgf. cm)
Approx. 3.0 N•m
(Approx. 30.6 kgf. cm)
Approx. 4.0 N•m
(Approx. 40.8 kgf. cm)
Approx. 5.8 N•m
(Approx. 59.1 kgf. cm)
ENG905-1
): 85 dB (A)
pA
): 96 dB (A)
WA
): 85 dB (A)
pA
): 96 dB (A)
WA
11