Publicité
CD Player
• CD-RWs, MP3 CD-ROMs, CD-I, CDV,VCD,
DVD or computer CDs are not possible for
playback on this set.
1 Adjust the source selector to CD.
2 Insert a CD/ CD-R with the printed side fac-
ing up and press the CD door gently close.
3 Press PLAY/PAUSE 2; on the set to start
playback.
4 To pause playback press PLAY/PAUSE 2;.
Press PLAY/PAUSE 2; again to resume
play.
5 To stop CD play, press STOP 9.
6 To switch off the set, adjust the source
selector to TAPE/
POWER OFF
check the cassette keys are released.
Note : CD play will also stop when:
- you open the CD compartment;
- you select TUNER or TAPE/
POWER OFF
sound source;
- the CD has reached the end of playback.
Selecting a different track
During playback you can use ∞ / § to select
a particular track.
- If you have selected a track number in the stop
or pause position, press PLAY/PAUSE 2; to
start playback.
• Press § once briefly for the next track, or
press repeatedly until the desired track num-
ber appears in the display.
• Press ∞ once briefly to return to the begin-
ning of a current track.
• Press ∞ repeatedly for a previous track.
Maintenance
Precautions & General
Maintenance (See 7)
• Place the set on a hard and flat surface so
that the system does not tilt.
• Do not expose the set, batteries, CDs to
humidity, rain, sand or excessive heat caused
by heating equipment or direct sunlight.
• Do not cover the set. Adequate ventilation
with a minimum gap of 6 inches between the
ventilation holes and surrounding surfaces is
necessary to prevent heat build-up.
• The mechanical parts of the set contain
self-lubricating bearings and must not be oiled
or lubricated.
• To clean the set, use a dry cloth. Do not use
any cleaning agents containing alcohol,
ammonia, benzene or abrasives as these may
harm the housing.
Tape deck maintenance (See 7)
To ensure quality recording and playback of
the tape deck, clean parts A, B and C as
shown, once a month. Use a cotton bud
All manuals and user guides at all-guides.com
Finding a passage within a
track
1 During playback, press and hold down ∞ /
§.
• The CD is played at high speed and low vol-
ume.
2 When you recognize the passage you want
release ∞ / §.
• Normal playback resumes.
Note : When searching within a final track
and you reach the end of the last track, the
CD goes to stop mode.
position and
Programming track
numbers
You may store up to 32 tracks in the desired
sequence. If you like, store any track more
than once.
1 In the stop position, press PROG to activate
programming.
Display shows 1 indicating the start of
the program. prog flashes. (See 5)
2 Press ∞ or § to select your desired track
number.
3 Press PROG to store the desired track
number.
Display shows you desired track number
briefly followed by a number, 2 (up to
32 in sequence) indicating the next
program location available. (See 6)
4 Repeat steps 2 to 3 to select and store all
desired tracks in this way.
Fu indicates the program memory is full
(when you have stored tracks on all 32
program locations).
5 To play your program, press PLAY/PAUSE
2;.
• Sudden changes in the surrounding
temperature can cause condensation on the
lens of your CD player. Playing a CD is then
not possible. Do not attempt to clean the
lens but leave the set in a warm environment
until the moisture evaporates.
• Always close the CD-tape door to avoid dust
on the lens.
• To clean the CD, wipe in a straight line from
the center towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.
• Never write on a CD or attach any stickers
to it.
CD Player
To review a program
• In the stop position, press PROG repeatedly
to see your stored track numbers.
Erasing a program
You can erase the contents of the memory
by:
– selecting TUNER or TAPE/
sound source;
– opening the CD door;
Display: prog disappears.
Cassette playback
1 Adjust the source selector to
TAPE/
.
POWER OFF
2 Press 9/ to open the cassette holder and
insert a cassette and close the deck.
3 Press 2 to start playback.
4 To pause playback press ;. To resume, press
the key again.
5 By pressing 5 or 6 , fast winding of the
tape is possible in both directions. To stop
fast winding, press 9/
6 To stop the tape, press 9/.
The keys are automatically released at the end
of a tape and the set switched off (unless
PAUSE mode ; has been activated.)
General information on recording
• Recording is permissible insofar as copyright
or. other rights of third parties are not
infringed.
• For recording, use only NORMAL type cas-
settes (IEC type I) on which the tabs have not
yet been broken.This deck is not suited for
recording on CHROME (IEC II) or METAL
(IEC IV) type cassettes.
Troubleshooting
If a fault occurs, first check the points listed below before taking the set for r
If you are unable to remedy a problem by following these hints, consult your
WARNING:
Do not open the set as there is a risk of elect
circumstances should you try to repair the set
invalidate the guarantee.
Problem
– Possible cause
• Remedy
No sound /power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
Display does not function properly/ No
reaction to operation of any of the con-
trols
– Electrostatic discharge
• Switch off and unplug the set. Reconnect after a
Casse
• The best recordin
Altering the VOL
recording.
• To protect a tape
break out the tabs
cover the tabs wit
Synchro Start C
POWER OFF
1 Select CD source
2 Insert a CD and i
numbers.
3 Press 9/ to open
a blank tape and
4 Press 0 to start r
Playing of the
matically from
gram. It is not
player separate
5 For brief interrup
recording, press ;
6 To stop recording
Recording from
1 Adjust the sourc
select your desire
2 Tune to the desire
reception).
3 Press 9/ to open
a blank tape and
4 Press 0 to start r
5 For brief interrup
recording, press ;
6 To stop recording
-- indication
– No CD inserted
• Insert a CD
– CD badly scratched o
• Replace/ clean CD,
– Laser lens steamed up
• Wait until lens has cl
– CD-R is blank or not f
• Use a finalized CD-
only
Poor cassette soun
– Dust and dirt on the h
• Clean deck parts, see
– Use of incompatible c
CHROME)
• Only use NORMAL
Publicité
