Publicité
English
Top and front panels (See 1)
1 VOLUME – to adjust volume level
2 Source selector : CD,TUNER,
TAPE/
POWER OFF
– selects CD, tuner or tape source of sound
– power off switch
3 CD door
4 TUNING – tunes to radio stations
5 BAND – selects waveband
6 PREVIOUS, NEXT ∞ , §
– skips or searches a passage/track
backwards or forward
7 PROG – programs and reviews
programmed track numbers
8 CASSETTE RECORDER keys:
; – pauses playback or recording
9/ – stops the tape;
– opens the cassette holder
5 or 6 – fast rewinds/ winds tape
2 – starts playback
0 – starts recording
9 Cassette door
0 CD Display – shows the CD functions
! PLAY/PAUSE 2; - starts or pauses CD
playback.
@ STOP 9 – stop playback;
– erases a CD program.
Back panel
# Telescopic antenna - improves FM
reception.
Note: AM band antenna is built into set
(see Tuner reception)
CD Player
• CD-RWs, MP3 CD-ROMs, CD-I, CDV,VCD,
DVD or computer CDs are not possible for
playback on this set.
1 Adjust the source selector to CD.
2 Insert a CD/ CD-R with the printed side fac-
ing up and press the CD door gently close.
3 Press PLAY/PAUSE 2; on the set to start
playback.
4 To pause playback press PLAY/PAUSE 2;.
Press PLAY/PAUSE 2; again to resume
play.
5 To stop CD play, press STOP 9.
6 To switch off the set, adjust the source
selector to TAPE/
POWER OFF
check the cassette keys are released.
Note : CD play will also stop when:
- you open the CD compartment;
- you select TUNER or TAPE/
POWER OFF
sound source;
- the CD has reached the end of playback.
Controls/Power Supply
All manuals and user guides at all-guides.com
$ Battery door - open to insert 6 x 1.5V
R-14/ UM2/ C-cells.
% AC POWER/MAINS - inlet for power
cord.
^ Voltage selector – (inside the battery
compartment, not all versions) adjust to
match the local voltage 110/220V before
plugging in the set.
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
Power Supply
Whenever convenient, use the mains supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1 Open the battery compartment and insert
six batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity
as indicated by the "+" and "–" symbols inside
the compartment. (See 1)
2 Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.
Batteries contain chemical substances, so
they should be disposed of properly.
Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst:
Finding a passage within a
track
1 During playback, press and hold down ∞ /
§.
• The CD is played at high speed and low vol-
ume.
2 When you recognize the passage you want
release ∞ / §.
• Normal playback resumes.
Note : When searching within a final track
and you reach the end of the last track, the
CD goes to stop mode.
position and
Programming track
numbers
You may store up to 32 tracks in the desired
sequence. If you like, store any track more
than once.
1 In the stop position, press PROG to activate
programming.
Power Supply
• Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
• When inserting new batteries, do not try to
mix old batteries with the new ones.
• Remove the batteries if the set is not to be
used for a long time.
Using AC Mains
1 Check if the power/mains voltage, as shown
on the type plate located on the
bottom of the set, corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2 Connect the power cord to the AC
POWER/MAINS inlet and the wall socket.The
mains lead is now connected and ready for
use.
3 To switch the set off completely, withdraw the
power cord from the wall socket.
• Disconnect the mains lead from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the bottom
of the set.
Switching POWER on/off:
Save energy
To avoid unnecessary energy consumption,
always adjust the source selector to
TAPE/
after using the set. Also
POWER OFF
check that the tape deck keys are released.
General operation
1 To select your sound source adjust the
source selector to : CD, TUNER or
TAPE/
.
POWER OFF
CD Player
To review a program
• In the stop position, press PROG repeatedly
to see your stored track numbers.
Erasing a program
You can erase the contents of the memory
by:
– selecting TUNER or TAPE/
sound source;
– opening the CD door;
Display: prog disappears.
Cassette playback
1 Adjust the source selector to
TAPE/
.
POWER OFF
2 Press 9/ to open the cassette holder and
insert a cassette and close the deck.
3 Press 2 to start playback.
4 To pause playback press ;. To resume, press
the key again.
5 By pressing 5 or 6 , fast winding of the
tape is possible in both directions. To stop
Tun
2 Adjust the sound
3 To switch off the
selector to TAPE
check the cassett
Tuner rece
1 Adjust the sourc
2 Adjust BAND to
band.
3 Turn TUNING
• For FM band sign
telescopic antenn
its length if the sig
• For MW (AM) b
built-in antenna. D
reception by turn
4 To switch off the
selector to TAPE
check the cassett
CD Player
Display indicati
– OP: (See 2) CD
– --: (See 3) re
disc/ error in C
R is blank or n
Troubleshootin
– During CD p
track number
– 2;: (See 4) pl
– prog: when CD
– Fu: program m
Playing a C
This CD player pla
including CD-Reco
Casse
• The best recordin
Altering the VOL
recording.
• To protect a tape
break out the tabs
cover the tabs wit
Synchro Start C
POWER OFF
1 Select CD source
2 Insert a CD and
numbers.
3 Press 9/ to open
a blank tape and
4 Press 0 to start r
Playing of the
matically from
gram. It is not
player separat
5 For brief interrup
recording, press ;
6 To stop recording
Publicité
