IMG STAGELINE PAK-15DMP Mode D'emploi page 7

Replacing the battery
1) Push the latch of the battery support to the
right (first arrow in the figure below) and pull
out the support (second arrow) .
1. 2.
2) Remove the discharged battery and insert
the new battery (3 V button cell of the type
CR 2025) into the support, positive pole
facing up .
3) Push the support back into the remote
control .
Never put discharged batteries in
the household waste . To protect the
environment, always take them to a
special waste disposal, e . g . collection
container at your retailer .
4 Operation
1) To switch on the speaker system, use the
mains switch POWER . The display will briefly
show "H I" and the green LED ON will light
up .
2) Use the controls LEVEL 1 and LEVEL 2 to adjust
the desired volume for the microphone con-
nected and / or for the units connected . Use
the control MP3 / BT / FM LEVEL to adjust the
volume for the MP3 player / radio / Bluetooth
module . If the module or an input is not used,
set the corresponding control to MIN .
CAUTION Never adjust a very high volume. Per-
manent high volumes may damage
your hearing! Your ear will get accus-
tomed to high volumes which do not
seem to be that high after some time. Therefore,
do not further increase a high volume after getting
used to it.
3) Model PAK-15DMP: Use the control MASTER
LEVEL to additionally adjust the total volume
of all mixed signals . However, this will not
affect the output level of the jack MIX OUT .
4) Use the controls TREBLE and BASS to adjust
the sound . This will not affect the sound of
the output signal of the jack MIX OUT .
5) If the red LED CLIP lights up, the volume is
too high which will result in distortion . If the
LED keeps lighting and there is substantial
distortion, the speakers may be damaged .
When the LED CLIP lights up, turn back the
corresponding control .
4.1 MP3 player / FM radio /
Bluetooth module
To switch on the module, use the button MODE,
if necessary: Keep the button pressed for 2 sec-
onds . All control options can be found in the
adjacent table .
To replay MP3 files, connect a USB flash drive or
a hard disk with separate power supply to the
USB port and /or
insert a memory card into the slot SD, notched
corner facing upwards and towards the unit .
To remove the card, push the card into the slot
until it disengages
Note: Due to the large number of storage device
manufacturers and device drivers, it cannot be guar-
anteed that all storage media are compatible with
the MP3 player .
Button
on the remote control 
on the unit 
To switch on / off: keep the button pressed for 2 seconds .
To switch over between:
1 . MP3 replay from a memory card (indication: SD)
MODE × ×
2 . MP3 replay via USB port (indication: USB)
3 . FM radio (indication: FM)
4 . Bluetooth receiver (indication: – – – – )
To adjust the volume ( in addition to the control MP3 / BT / FM LEVEL
VOL− VOL+ ×
MUTE × To mute and unmute the sound
 II × × To switch between replay and pause
Repeat function and random replay
= repeat of the title
×
= repeat of all titles
= continuous replay of the titles in random order
I    I × × Title beginning, previous / next title
For direct title selection, examples:
Title
8
0 ... 9
15
100+ ×
100
200+
103
124
250
EQ × To select sound settings
STOP × To stop the replay
To find all radio stations and to store them automatically one after another:
Keep the button pressed for 2 seconds until the numbers of the frequency indica-
 II ×
tion start scrolling .
In the radio mode, the button II on the remote control is without function .
0 ... 9 × To call up a stored station
Press briefly: previous / next station
I     I × ×
Keep pressed for 1 second to start station scanning .
1 . Press the button MODE repeatedly until – – – – starts flashing on the display .
2 . Activate the Bluetooth function of the Bluetooth signal source
(refer to manual of the Bluetooth signal source, if required) .
MODE × ×
3 . Link the Bluetooth signal source to the active speaker system .
When the connection has been made, the display will stop flashing .
4 . Start the replay on the Bluetooth signal source .
 II × × To switch between replay and pause
I     I × × Title beginning, previous/next title
¹ The Bluetooth signal source must use the A2DP profile
(Advanced Audio Distribution Profile); otherwise, wire-
less transmission will not be possible .
Specifications
Amplifier power (RMS / MAX)
Frequency range
Max. SPL
Bass speaker
Tweeter
Inputs (sensitivity/ impedance)
Mic XLR, bal.
Mic 6.3 mm jack, unbal.
Line 1 XLR, bal.
Line 1 6.3 mm jack, unbal.
Line 2 3.5 mm jack, unbal.
Line 2 RCA, unbal.
Line 2 XLR, bal.
Ambient temperature
Power supply
Max. power consumption
Dimensions (W × H × D) 240 × 390 × 200 mm
Weight
All rights reserved by MONACOR
®
reproduced in any form or by any means for any commercial use.
Function
MP3 player / radio / Bluetooth module
on the speaker system)
MP3 player
Button(s)
8
1, 5
100+
100+, 3
100+, 9, 9, 6
200+, 9, 9, 9, 9, 9, 5
FM radio
Bluetooth receiver 1
2
2
² The Bluetooth signal source can only be controlled via
the active speaker system if it uses the AVRC profile
(Audio Video Remote Control Profile) .
PAK-8DMP PAK-10DMP
60 W / 120 W 80 W / 150 W
60 Hz – 20 kHz 55 Hz – 20 kHz
117 dB 113 dB
20 cm (8") 25 cm (10")
dynamic horn tweeter, 25 mm (1")
20 mV/ 10 kΩ 25mV/ 10 kΩ
50 mV/ 20 kΩ 65 mV/ 20 kΩ
300 mV/ 10 kΩ 470 mV/ 10 kΩ
730 mV/ 20 kΩ 1000 mV/ 20 kΩ
450 mV/ 48 kΩ 500 mV/ 50 kΩ
450 mV/ 48 kΩ 500 mV/ 50 kΩ
— —
0 – 40 °C
230 V/ 50 Hz 230 V/ 50 Hz
140 VA 170 VA
320 × 490 × 250 mm
5.8 kg 8 kg
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
PAK-12DMP PAK-15DMP
90 W / 180 W 120 W / 200 W
50 Hz – 20 kHz 45 Hz – 20 kHz
115 dB 117 dB
30 cm (12") 38 cm (15")
12 mV/ 2 kΩ 30 mV/ 1 kΩ
30 mV/ 4 kΩ 75 mV/ 2 kΩ
— —
— —
500 mV/ 8 kΩ 500 mV/ 8 kΩ
500 mV/ 8 kΩ 500 mV/ 8 kΩ
460 mV/ 8 kΩ 600 mV/ 8 kΩ
230 V/ 50 Hz 230 V/ 50 Hz
200 VA 220 VA
370 × 590 × 290 mm 445 × 700 × 360 mm
11.2 kg 16 kg
Subject to technical modifications .
7