Ergomotion ADJUSTABLE BASE quest 1.5 Manuel Du Propriétaire page 4

safety precautions and usage statements
platform support of the base. This contact may result in metal on metal or
metal on plastic contact. This applies slight tension on the moving components
and resonance is reduced to a minimum level. If excessive noise or vibration is
experienced, reverse the movement action (up or down) of the base with the
remote control. This should realign the base's activating mechanisms to the
proper operational position. In normal base operation, the wheels, which allow
the bed to maintain its distance from the wall, will make contact with the steel
platform supports of the base creating a contact noise. When entering, exiting
or shifting weight on the base, this contact noise may be audible as the wheels
make contact. This is normal.
MATERIALS:
Ergo adjustable bases are constructed from various materials including woods,
metals, plastics and fabrics. Tension, pressure or movement applied to the
frame, platform or shroud through general use may create an audible sound.
TOLERANCE:
All Ergo adjustable foundations, depending on make and model, are designed
and manufactured to perform and function within designated quality control
parameters. Bases are subject to meticulous and rigorous inspections during
the quality control process to ensure bases will operate within these standards
during normal operating use. Normal operating use is defined as the following:
Adjustable foundation is to be operated with a mattress and load. Testing
procedures require lifetime cycle tests
with up to 120kg distributed load. The angle
(designated "α" in illustration) between the
back section and the flat section for various
configurations of the mattress support
platform shall be ± 3°, which translates
to a tolerance of up to 1 ½". The angle
(designated "β" in figure) between the flat
section and foot section for various configurations of the mattress support
platform shall be ± 3°, which translates to a tolerance of up to ¾". Any
adjustable foundation deemed to be within these allocated tolerances is
considered to have met the manufacturer's quality control standards.
2
THAT "NEW PRODUCT" SMELL:
Some people notice a slight odor to their new adjustable base—this can come
from our material manufacturing process. This smell is normal and usually
disappears before the product reaches you. Sometimes, however, this smell
may still be noticeable. It usually disappears after a few weeks, providing
adequate ventilation of the product and the environment.
BREAK IN PERIOD:
You can speed up the break-in period by simply spending time in the
adjustable bed through activities such as reading, watching TV or playing with
the kids or grandkids. The extra movement will help the adjustable base
respond to weight and temperature changes. Some of the materials in our
adjustable bases such as the woods, metals and plastics used in the platform,
frame and components are sensitive to moisture content and temperature
and may make sounds in colder environments.
PAIRED OPERATION:
When operating a "paired" split base setup there may be a time latency up to
1.5 seconds between each bases articulation.
WEAR AND TEAR:
Wear and tear is damage that naturally and inevitably occurs as a result of
normal use or aging.
FABRIC CARE:
(α°)
To prolong the life of your fabric, protect from direct sunlight whenever
possible. For spot cleaning, wipe area with a light damp sponge or vacuum
(β°)
with a soft brush attachment to remove particles. Keep at a minimum of 30cm
(12 inches) away from direct heat sources. For a deeper cleaning, blot liquid
spills with a clean dry cloth. Wipe with a clean cloth dampened with warm
water. Do not wet excessively. A soft bristle brush may be used to remove
ingrained soil. Avoid scratching by gentle brushing. Wipe with a clean cloth
dampened with warm water to remove residues. Dry in shade away from
direct heat. If persistent marks remain visible after cleaning, seek professional
advice.
Adjustable
Bed Tolerance
All Ergomotion adjustable foundations, depending on make and model, are designed and manufactured to perform and
function within designated quality control parameters. Bases are subject to meticulous and rigorous inspections during
the quality control process to ensure bases will operate within these standards during normal operating use.
Normal operating use is defined as the following:
-Adjustable foundation is to be operated with a mattress and load. Testing procedures require lifetime cycle
tests with up to 120kg distributed load.
The angle (designated "α" in figure 1) between the back section and the flat section for various configurations of the
mattress support platform shall be ± 3°, which translates to a tolerance of up to 1 ½".
The angle (designated "β" in figure 1) between the flat section and foot section for various configurations of the mattress
support platform shall be ± 3°, which translates to a tolerance of up to ¾".
When operating a "paired" split base setup there may be a time latency up to 1.5 seconds between each bases articulation.
Any adjustable foundation deemed to be within these allocated tolerances is considered to have met the manufacturer's
quality control standards.
Blake Pettit
Quality Assurance Manager
Ph 805-979-3875
Fx 805-979-9399
www.ergomotion.com
Ergomotion Inc. | ph 1-888-550-3746 | fx 805-979-9399 | www.ergomotion.com