EINHELL TC-SD 3,6 Li Instructions D'origine page 17

6. Operation
6.1 Charging the battery (Fig. 2)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is
fl at. In this case the bit chuck will cease to turn.
Notice! Do not press the On/Off switch any more
if the protective circuit has tripped. This may da-
mage the battery.
Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the battery charger in the plug socket and
connect the charging cable to the charging con-
nection. The charging process starts as soon as
the charging cable is connected to the charging
adapter.
The red LED (4) will come on to indicate that the
battery pack is being charged.
The charging control lamp (4) goes out when
charging is completed.
Notice! The handle may become a little warm du-
ring the charging process. This is normal.
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
•
the charging unit
•
and the screwdriver
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
Anl_TC_SD_3_6_Li_SPK9.indb 16 Anl_TC_SD_3_6_Li_SPK9.indb 16
GB
scharged. This will cause it to develop a defect.
6.2 Changeover switch (Fig. 3/Item 10)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. Change the direction of rota-
tion only when the equipment is at a standstill.
If you fail to observe this point, the gearing may
become damaged. When the slide switch is in the
middle position, the On/Off switch is blocked.
6.3 On/Off switch (Fig. 3 / Item 9)
Press the On/Off switch to switch the cordless
screwdriver on. Release the On/Off switch again
to switch it off .
6.4 LED lamp (Fig. 3/Item 2)
The LED lamp (2) can be used in poor lighting
conditions to illuminate the area where you want
to screw. To switch ON, press the switch (3) and
to switch OFF press the switch (3) again.
6.5 Angle setting (Fig. 4/Item 7)
The screwdriver can be locked into 2 diff erent
angle settings. To do so, press and hold the lo-
cking button (7) and move the screwdriver into the
desired position. Then release the locking button
(7) again.
Caution! Before you switch on the screwdriver,
make sure that it is correctly locked in the angle
position in question.
6.6 Battery capacity indicator (Fig. 5)
Remove the cordless screwdriver from the char-
ging unit/charging station.
Press the button for the battery capacity indicator
(6). The battery capacity indicator (5) indicates
the charge state of the battery on 3 colored LEDs.
All the LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
- 16 -
Autogoods "130"
09.01.2020 13:53:13 09.01.2020 13:53:13