Publicité
Les langues disponibles
Les langues disponibles
Press the dotted point on the siphon in the softener
compartment and pull towards you until the
compartment is removed from the machine.
C
If more than normal amount of water and
softener mixture starts to gather in the softener
compartment, the siphon must be cleaned.
Wash the detergent drawer and the siphon with
plenty of lukewarm water in a washbasin. Wear
protective gloves or use an appropriate brush to
avoid touching of the residues in the drawer with
your skin when cleaning. Insert the drawer back
into its place after cleaning and make sure that it is
seated well.
Cleaning the loading door and the drum
Residues of softener, detergent and dirt may
accumulate in your machine in time and may cause
unpleasant odours and washing complaints. To
avoid this, use the Drum Cleaning programme.
If your machine does not have a Drum Cleaning
programme, use Cotton-90 programme. Before
starting the programme, put max. 100 g of powder
anti-limescale into the main wash detergent
compartment (compartment nr. II). If the anti-
limescale is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the bellow with
a clean piece of cloth after the programme has
come to an end.
C
Repeat Drum Cleaning process in every 2
months.
C
Use an anti-limescale suitable for the washing
machines.
After every washing make sure that no foreign
substance is left in the drum.
If the holes on the bellow shown in the figure is
blocked, open the holes using a toothpick.
C
Foreign metal substances will cause rust stains
in the drum. Clean the stains on the drum
surface by using cleaning agents for stainless
steel. Never use steel wool or wire wool.
Cleaning the body and control panel
Wipe the body of the machine with soapy water
or non-corrosive mild gel detergents as necessary,
and dry with a soft cloth.
Use only a soft and damp cloth to clean the control
panel.
A
Never use sponge or scrub materials. These
will damage the painted and plastic surfaces.
Cleaning the water intake filters
There is a filter at the end of each water intake valve
at the rear of the machine and also at the end of
each water intake hose where they are connected
to the tap. These filters prevent foreign substances
and dirt in the water to enter the washing machine.
Filters should be cleaned as they do get dirty.
All manuals and user guides at all-guides.com
Close the taps. Remove the nuts of the water intake
hoses to access the filters on the water intake
valves. Clean them with an appropriate brush. If the
filters are too dirty, take them out by means of pliers
and clean them. Take out the filters on the flat ends
of the water intake hoses together with the gaskets
and clean thoroughly under running water. Replace
the gaskets and filters carefully in their places and
tighten the hose nuts by hand.
Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid
items such as buttons, coins and fabric fibers
clogging the pump impeller during discharge of
washing water. Thus, the water will be discharged
without any problem and the service life of the
pump will extend.
If the machine fails to drain water, the pump filter
is clogged. Filter must be cleaned whenever it
is clogged or in every 3 months. Water must be
drained off first to clean the pump filter.
In addition, prior to transporting the machine (e.g.,
when moving to another house) and in case of
freezing of the water, water may have to be drained
completely.
A
In order to clean the dirty filter and discharge the
water:
Unplug the machine to cut off the supply power.
A
Open the filter cover by pulling it from both sides at
the top.
C
11 - EN
Foreign substances left in the pump filter may
damage your machine or may cause noise
problem.
Temperature of the water inside the machine
may rise up to 90 ºC. To avoid burning risk, filter
must be cleaned after the water in the machine
cools down.
You can remove the filter cover by slightly
pushing downwards with a thin plastic tipped
tool, through the gap above the filter cover. Do
not use metal tipped tools to remove the cover.
Publicité
