Publicité
Les langues disponibles
Les langues disponibles
EN
2. Connections on Home-Cinema amplifier and Home-cinema preamplifier
ALL THE CONNECTIONS MUST BE MADE WITH THE EQUIPMENT TURNED OFF.
It is essential to connect the speakers using the correct polarity. Make sure to connect the
" + " terminal of the speaker (Red) to the " + " output terminal of the amplifier. Then, make
sure to connect the " - " terminal of the speaker (Black) to the " - " output terminal of the
amplifier. A wrong connection would cause a cribled stereo image and loss of bass. Use
high quality speaker cable. Elipson speakers are supplied configured for use in a single
wired mode or bi-wiring. Bi-amp is also possible (see page 31).
FRONT
FRONT
CENTER
R
L
•SW
•FR
•FL
•C
SUB8
24F
24F
11C
or
or
or
or
SUB10*
14F*
14F*
14C*
or
or
or
or
SUB12*
34F*
34F*
14LCR*
or
or
14LCR*
14LCR*
Speaker
Enter
•FR/FL
FRONT RIGHT/LEFT
•C
CENTER
•SR/SL
SURROUND RIGHT/LEFT
•SBR/SBL
SURROUND BACK RIGHT/LEFT
•SW
SUBWOOFER
•FHL/FHR
HEIGHT RIGHT/LEFT
*Depending your model
PRE OUT
PRE OUT
SUBWOOFER
SUBWOOFER
RCA SUB
RCA SUB
SPEAKERS
SPEAKERS
SURROUND
SURROUND
SURROUND
SURROUND
HEIGHT
R
L
BACK R
BACK L
R
•SR
•SL
•SBR
•SBL
•FHR
7SR
7SR
7SR
7SR
6ATM
or
or
or
or
14LCR*
14LCR*
14LCR*
14LCR*
•SBR
•SBL
6B
6B
or
or
8B*
8B*
Description
Speaker Front right (R) /Left (L)
Central Speaker
Surround speaker right (R) /Left (L)
Surround back speaker right (R) /Left (L)
Subwoofer
Atmos speaker Front right (R) /Left (L)
30
VII. USE
1. Burn-in period
When you take them out of the packaging, the Prestige Facet speakers are not yet able to
reproduce with the same efficiency all the sound frequencies they are supposed to play.
The Prestige Facet range loudspeakers are complex mechanical assemblies which need a
period of adaptation ("burn-in") to operate at their best and become acclimatised to the
temperature and humidity conditions of your environment. This burn-in period may last for
some weeks, but you can quicken it by operating the speakers between 50 and 100 hours
consecutively, on a moderate volume and broadcasting a radio station.
2. Bi-wiring and bi-ampification (All models, except PF6ATM and PF7SR)
Bi-wiring can increase the performance of your loudspeakers. Only one amplifier is
necessary, but two distinct cables are used to, individually, powered the treble drivers
and the bass drivers on the speaker. Good quality cables are required for an efficient bi-
wiring. The Prestige Facet speaker have a 4 terminals binding post, allowing bi-wiring and
bi-amplification.
Top terminals for treble, bottom terminals for bass. For a mono-amplification use, connect
the terminals with the metallic straps and connect the cables on 2 terminals.
For a bi-amp, two amplifiers are used separately for treble and bass
HEIGHT
Note: The PF7SR and PF6ATM models have a single binding terminal.
L
3. Choice of cables
Choose high quality cables with a cross-section appropriate to their length. You can also
replace the provided metallic straps by a strap using the same speaker cable you use to
connect your loudspeakers to your amplifier. Your Elipson dealer will be able to advise you.
4. Choice of amplifier
Your setup type (stereo or home-cinema) will determine the choice of the appropriate
amplifier. Your dealer will be able to advise you on the most suitable amplifier for your system.
•FHL
5. Cleaning instructions
6ATM
To improve the lifetime of your speakers, we recommend regular cleaning. A soft cloth will
be enough for dusting. If the speaker is stained, we recommend simply using a damp cloth
with some mild soap if necessary. The lacquered front panel can be cleaned with a soft
cloth and standard glass cleaning product.
Never use solvents, detergents, alcohol-based or corrosive products, scrapers or scourers
to avoid any damage on the speaker surface.
Keep the loudspeakers away from sources of heat.
31
Publicité
