Livington M23647 Mode D'emploi page 19

connector (power circuit) as the steam cleaner.
OPERATION
Prior to first time use, remove all labels, protective foils or wrapping.
ASSEMBLING THE LIVINGTON PRIME STEAM SCRUBBER
WARNING: Ensure that the appliance is unplugged before assembling the appliance or replacing an accessory.
1. Slide the lower end of the main element into the Mop-swivel joint until it snaps into place.
2. Insert the extension tube 2 into the body of the appliance, as seen in Illustration 1.
3. As shown in the figure eptput the cloth pad on the groud, pick up the body onto the cloth pad, and the cloth pad will be stick on
the scrubber, also it can be use on the carpet with glider. (Figure 2.).
4. Press the water tank release knob and remove it with gentle pressure from the body of the appliance (illustration 3)
5. Open the water tank as illustrated below (illustration 4), fill it as far as the maximum upper edge with water, then reinsert it in the
appliance. Check that the water tank is securely placed in the appliance.
Please Note: You may use tap water in the Livington PRIME Steam Scrubber. In areas with hard water, we recommend the use of
distilled water for a better performance.
6. Insert the power cable plug into an earthed socket and press the main switch to turn the appliance on.
Use of the Flexible Function
To use the flexible function, manipulate the flexible mechanism to bring the steam cleaner to another angle. You will be able to reach
and clean particular spots, such as the floor underneath your sofa, easily. Illustration 5.
Carpet Gliders: When using the Livington PRIME Steam Scrubber on carpet surfaces: Place the mop-top with mounted micro-fibre
cloth on the carpet gliders, as shown in (illustration 6).
Please Note: Never remove or install accessories while the appliance is in operation. Do not use the Livington PRIME Steam Scrubber
on carpet surfaces witout the carpet gliders. Never use the carpet gliders on surfaces that are prone to scratches. Verwendung des
Livington PRIME Steam Scrubber
USING THE LIVINGTON PRIME STEAM SCRUBBER
With the Livington PRIME Steam Scrubber, floor surfaces such as, marble, ceramic, carpet, stone, linoleum, sealed hardwood floors
and parquet can be cleaned.
Please Note: This product emits damp and creates humidity. Water marks, stains or damage can appear on floors if the appliance is
operated on one spot for too long.
• Do not use the appliance on untreated floors and do not leave it to stand for long periods of time on wood or heat-sensitive surfaces. This
could cause the wood grain to rise, as well as other types of damage.
• Take particular care when using the appliance on vinyl, linoleum or other heat-sensitive floors. Too much heat can lead to the melting
of adhesive in the floor. Only use the appliance on laminated floors that have been professionally laid and exhibit no cracks or gaps that
would allow dampness to enter.
• Test the Livington PRIME Steam Scrubber on a small, isolated part of your floor surface before using it extensively over the whole area.
• Only use the carpet gliders on carpet surfaces or carpet rugs. The use of the carpet gliders on all other floor surfaces may possibly lead to
streaks or scratches.
1. Fill the water tank with water. Replace the water tank covering. Ensure that the copper cone in the water tank (illustr.7) is always
completely submerged in water during operation.
Please Note: In isolated cases the visible hose in the water tank can bend into a kink. This impairs operation. Please eliminate the kink from
the hose.
TIPP: For an especially fresh aroma when cleaning, we recommend the use of Livington Steam Fragrance. This is available as an
alternative accessory. It is particularly suitable for households with animals. Simply add 2 to 3 squirts to the Livington PRIME Steam
Scrubber water reservoir.
2. Insert the mains plug into an earthed socket. Activate the power-on button and the indicator light will switch on.
3. The Livington Prime Steam Mop utilizes Opti Steam technology; No matter which attachment or surface you are working with, the
Livington Prime Steam Mop always works at the ideal temperature or optimal steam output. Please note that the device may drip from
the time it is started up until the target temperature is reached. This is not a malfunction, but a normal part of the heating up process.
To activate the scrubber (vibration function), press the ON/OFF switch (FIG. 11). 6000 vibrations per minute loosens even deep-set dirt
without the need for scrubbing. To end the process, simply press the ON/OFF switch again.
TIP: In instances of stubborn dirt, run over the affected area at a very slow speed to increase the effect.
TIP: The Livington Steam Mop is ideally suited to the cleaning of all hardwood floors, such as linoleum, ceramic, marble, wood etc.
Ideal for the cleaning of carpets and rugs, bathrooms, kitchens, window sills, car wheels etc.
4. Move the appliance slowly over the surface to be cleaned. The absorbent mop soaks up the dirt that has been dissolved by the
steam. Use the steam generously. Keep a hand towel ready to wipe away any excess water that may accumulate.
5. As soon as the Livington PRIME Steam Scrubber stops emitting steam, refill the water container for further cleaning and resume
cleaning or deactivate the appliance and end the cleaning process. The Livington PRIME Steam Scrubber has the option of filling
up the tank while in activated mode, as it has an automatic water system at its disposal which stops the steam process as soon as
M23647/M27861_Livington_PRIME_steamscrubber_Manual_20210601_KS.indd 19 M23647/M27861_Livington_PRIME_steamscrubber_Manual_20210601_KS.indd 19
19
01.06.21 10:20 01.06.21 10:20