Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-5598
IGLOO PARTY BAR
TOOLS NEEDED
Wrench
Lid x 1
Rigid
Locking
Caster x 2
Caster x 2
Figure 1
Short
Screws
Long Screws
PAGE 1 OF 9
All manuals and user guides at all-guides.com
1-800-295-5510
uline.com
Phillips
Screwdriver
Caster Mounting
Hardware x 16
Opener x 1
INSTALLATION
Mounting
Bracket
Cooler
PARTS
Cooler x 1
Bottle
Short
Screw x 2
1.
Remove two short screws and bottle opener from
bag. Line up the bottle opener with the two most
upper holes. Using the Phillips screwdriver, tighten
the short screws into the cooler. (See Figure 1)
NOTE: The holes are not pre-cut, but are
marked with indentations in the cooler wall.
2. Attach mounting bracket to cooler wall using the two
long screws. Make sure mounting bracket is upright
(See Figure 1)
NOTE: The holes are not pre-cut, but are
marked with indentations in the cooler wall.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Base x 1
Mounting
Long
Bracket x 1
Screw x 2
Cap Catch
Bin x 1
0521 IH-5598
Publicité
Manuels Connexes pour Uline IGLOO H-5598
Sommaire des Matières pour Uline IGLOO H-5598
- Page 1 Para Español, vea páginas 4-6. All manuals and user guides at all-guides.com Pour le français, consulter les pages 7-9. H-5598 1-800-295-5510 uline.com IGLOO PARTY BAR TOOLS NEEDED Wrench Phillips Screwdriver PARTS Base x 1 Lid x 1 Cooler x 1...
- Page 2 All manuals and user guides at all-guides.com INSTALLATION CONTINUED 3. Slide the cap catch bin onto the mounting bracket. Figure 2 (See Figure 2) 4. Connect the lid by pushing the three pins into the Figure 3 clips located on the cooler. (See Figure 3) 5.
- Page 3 • The cooler is equipped with a hose-compatible threaded drain plug. To drain liquid away from area of use, attach a standard garden hose to the cooler drain plug and direct the open end of disposal area. 1-800-295-5510 PAGE 3 OF 9 0521 IH-5598 uline.com...
- Page 4 All manuals and user guides at all-guides.com H-5598 800-295-5510 uline.mx IGLOO PARTY BAR HERRAMIENTAS NECESARIAS Llave Desarmador de Cruz PARTES 1 Base 1 Tapa 1 Hielera 2 Ruedas 2 Ruedas 16 Accesorios 1 Abrebotellas 2 Tornillos 1 Soporte 2 Tornillos...
- Page 5 All manuals and user guides at all-guides.com CONTINUACIÓN DE INSTALACIÓN 3. Deslice la gaveta para recolectar tapas en el Diagrama 2 soporte de montaje. (Vea Diagrama 2) 4. Fije la tapa insertando los tres pasadores en los Diagrama 3 clips ubicados en la hielera ejerciendo presión. (Vea Diagrama 3) 5.
- Page 6 800-295-5510 PAGE 6 OF 9 0521 IH-5598 uline.mx...
- Page 7 All manuals and user guides at all-guides.com H-5598 1-800-295-5510 uline.ca IGLOO – GLACIÈRE OUTILS REQUIS Clé Tournevis cruciforme PIÈCES Base x 1 Couvercle x 1 Glacière x 1 Roulette Roulette Matériel Décapsuleur x 1 Support de Bac à rigide x 2 verrouillable x 2...
- Page 8 All manuals and user guides at all-guides.com INSTALLATION SUITE 3. Glissez le bac à capsules sur le support de fixation. Figure 2 (Voir Figure 2) 4. Installez le couvercle en insérant les trois tiges Figure 3 dans les fentes des supports situés sur la glacière. (Voir Figure 3) 5.
- Page 9 à un tuyau. Pour vider le liquide hors de la zone d'utilisation, fixez un tuyau d'arrosage standard au bouchon de vidange de la glacière et orientez l'extrémité ouverte vers la zone de rejet. 1-800-295-5510 PAGE 9 OF 9 0521 IH-5598 uline.ca...