Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-9806
DESIGNER COLLECTION –
MOBILE PEDESTAL FILE
TOOLS NEEDED
Phillips
Screwdriver
A
Caster x 2
E
Handle x 3
Figure 1
Caster
A
H
PAGE 1 OF 6
Drill
B
Locking Caster x 2
F
M4 x 34 mm Screw x 6
Locking
Caster
H B
1-800-295-5510
uline.com
PARTS
C
Drawer Caster x 1
G
Metal Bar x 1
ASSEMBLY
NOTE: Check that all parts are included.
NOTE: Assemble unit on a smooth, non-marring
surface to prevent scratching.
NOTE: Tighten all screws with Phillips screwdriver.
1.
Remove casters and hardware from drawers.
2. Lock drawers using key and flip product upside
down. Align holes on the locking caster (B) with the
pre-drilled holes near the front of the unit. Attach
using eight ST3.5 x 14 mm screws (H). (See Figure 1)
3. Align holes on casters (A) with the pre-drilled holes
toward the back of the unit. Attach using eight
ST3.5 x 14 mm screws (H). (See Figure 1)
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
D
File Clip x 2
H
I
ST3.5 x 14 mm
Keys (Set of 2) x 1
Screw x 19
0322 IH-9806
Publicité
Manuels Connexes pour Uline DESIGNER H-9806
Sommaire des Matières pour Uline DESIGNER H-9806
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-9806 1-800-295-5510 uline.com DESIGNER COLLECTION – MOBILE PEDESTAL FILE TOOLS NEEDED Phillips Screwdriver Drill PARTS Caster x 2 Locking Caster x 2 Drawer Caster x 1 File Clip x 2...
- Page 2 M4 x 34 mm screws (F). Repeat for other drawers. (See Figure 3) 6. Attach file clips (D) to each side of the bottom Figure 4 drawer and insert metal bar (G). (See Figure 4) 1-800-295-5510 uline.com PAGE 2 OF 6 0322 IH-9806...
- Page 3 H-9806 800-295-5510 uline.mx COLECCIÓN DE DISEÑO – ARCHIVERO MÓVIL DE PEDESTAL HERRAMIENTAS NECESARIAS Desarmador de Cruz Taladro PARTES 2 Ruedas 2 Ruedas 1 Rueda de Cajón 2 Clips para con Seguro Carpetas 3 Asas 6 Tornillos M4 x 34 mm...
- Page 4 (Vea Diagrama 3) 6. Fije los clips para archivo (D) a cada lado del cajón Diagrama 4 inferior e inserte la barra de metal (G). (Vea Diagrama 4) 800-295-5510 uline.mx PAGE 4 OF 6 0322 IH-9806...
- Page 5 H-9806 1-800-295-5510 uline.ca COLLECTION DESIGNER – CLASSEUR MOBILE À CAISSON OUTILS REQUIS Tournevis cruciforme Perceuse PIÈCES Roulette x 2 Roulette blocable x 2 Roulette de tiroir x 1 Attache pour classeur x 2 Poignée x 3 Vis M4 x 34 mm x 6 Barre métallique x 1...
- Page 6 (Voir Figure 3) 6. Fixez les attaches pour classeur (D) de chaque côté Figure 4 du tiroir du bas, puis insérez la barre métallique (G). (Voir Figure 4) 1-800-295-5510 uline.ca PAGE 6 OF 6 0322 IH-9806...