Black & Decker Scumbuster Serie Mode D'emploi page 6

ENGLISH
9. Mild scrub pad (white): for milder scrubbing of large areas,
such as ceramic tile walls and floors or outdoor furniture
10. Coarse scrub pad (light blue): for aggressive scrubbing of
larger surfaces, such as ceramic tile walls and floors or
bath tubs and sinks (porcelain or enamel)
11. Heavy scrub pad (green): for aggressive scrubbing on
large surfaces, such as barbecue grill grates
12. Radial brush: for tile grout cleaning
13. Narrow brush: for cleaning of corners and hard to reach
places
14. Carpet brush: for carpet cleaning
15. Flexible attachment: for use of brushes and scrub pads in
curved places
16. Carrying caddy: for portable and convenient storage of the
unit and accessories
17. Wall mount: for storage of the unit during charging
18. Cleaning stick: for unclogging of the dispensing system
Installation
Mounting the wall mount to the wall (fig. B)
The wall mount can be fitted to the wall to provide a
convenient storage and charging point for the appliance.
Locate the wall mount (17) within reach of a mains supply.
x
Fit the wall mount using the appropriate hardware.
Plug in the charger.
x
Insert the cord of the charger into the groove (19) in the
x
bottom of the wall mount. Allow sufficient length of cord
to connect the charger plug (20) to the appliance when
placed in the wall mount.
Warning! Do not fit the wall mount directly over a mains
supply. Ensure the cord has a loop when the charger is
connected to the mains.
Assembly
Warning! Before assembly, switch off the tool.
Fitting and removing an accessory (fig. C)
Fitting
When using a pad, fit the pad onto the pad disc.
x
Align the triangular notch on the accessory with the shaft
x
on the motor unit.
Place the accessory onto the shaft. Snap and twist the
x
accessory quickly in the clockwise direction.
Removing
Snap and twist the accessory quickly in the
x
counterclockwise direction and pull it off the motor unit.
6
All manuals and user guides at all-guides.com
Fitting flexible attachment (fig. D)
The flexible attachment (15) must be fitted between the motor
unit and the accessory.
x
x
Warning! Never use the flexible attachment without a brush
or scrub pad in place. Do not use the flexible attachment for
carpet cleaning.
Use
x
x
x
Charging the battery (fig. E)
x
x
x
x
The indicator light on the charger will be lit and will stay lit as
long as the battery is connected to the charger.
x
Whilst charging, the charger may become warm. This is normal
and does not indicate a problem. The appliance can be left
connected to the charger indefinitely.
x
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
Filling the liquid reservoir (fig. F)
Fill the appliance only with water-like household cleaning
agents. Do not fill the appliance with gels or soft scrubs as
they will clog the dispensing system.
x
x
x
x
Warning! Before filling the appliance with a different
cleaning agent, always clean the housing and flush the
dispense system with clear water. Do not mix cleaning agents.
Fit the flexible attachment onto the appliance as
described above.
Fit the accessory onto the appliance flexible attachment.
Before first use, the battery must be charged for at least
16 hours.
Place the appliance in the wall mount whenever it is not
in use.
Leave the appliance connected to the charger whenever it
is not in use.
Before charging, make sure that the appliance is switched
off.
Place the appliance in the wall mount (17) as shown.
Insert the charger plug (20) into the charger connector (6)
at the rear of the appliance.
Plug in the charger. Switch on at the mains.
Leave the appliance to charge for at least 16 hours.
After disconnecting the appliance from the charger,
replace the charging plug.
Hold the appliance over a sink with the nozzle (3) facing
down as shown.
Loosen the liquid reservoir cap (21) and remove it.
Fill the reservoir (5) with the required cleaning agent up to
the "max" line.
Re-fit the cap, making sure it is tightened securely.