Makita LH1040 Manuel D'instructions page 16

For all countries other than European countries
CAUTION:
• The silver ring 25.4 mm in outer diameter is factory-
installed onto the spindle. The black ring 25 mm in
outer diameter is included as standard equipment.
Before mounting the blade onto the spindle, always be
sure that the correct ring for the arbor hole of the blade
you intend to use is installed onto the spindle. (Fig. 20)
For European countries
CAUTION:
• The ring 30 mm in outer diameter is factory-installed
between the inner and outer flanges. (Fig. 20)
Return the lower blade guard A and center cover to its
original position. Then tighten the hex bolt clockwise to
secure the center cover. Raise the blade guard B as far
as it will go and tighten the clamping screw firmly while
holding it in the raised position. Lower the handle to
make sure that the lower blade guards move properly.
Make sure shaft lock has released spindle before making
cut.
Adjusting riving knife
Before adjusting the riving knife, loosen the two levers by
turning counterclockwise and press the top table on the
right side nearby the riving knife to its lowered position.
Then secure the top table by firmly re-tightening the two
levers as shown in the figure. (Fig. 21)
There must be a clearance of about 4 – 5 mm between
the riving knife and the blade teeth. Adjust the riving knife
accordingly by loosening two hex bolts counterclockwise
with the hex socket wrench and measuring the distance.
Tighten the hex bolts securely, and then check to see that
the top blade guard works smoothly before cutting.
(Fig. 22)
The riving knife has been installed before shipment from
the factory so that the blade and riving knife are in a
straight line. (Fig. 23)
CAUTION:
• If the blade and riving knife are not aligned properly, a
dangerous pinching condition may result during opera-
tion. Make sure they are properly aligned. You could
suffer serious personal injury while using the tool with-
out a properly aligned riving knife. If they are not
aligned for any reasons, always have Makita authorized
service center repair it.
Installing and adjusting rip fence
1. Install the rip fence on the table so that the rip fence
holder engages with the guide rail. Tighten the
clamping screw (B) of the rip fence firmly clockwise.
2. Loosen the clamping screw (A).
3. Slide the rip fence and secure it so that the far end
from you of the rip fence is aligned with the point at
which the front edge of saw blade just appears from
top surface of the workpiece. The purpose of this
adjustment is to reduce risk of kick-back toward
operator that cut piece from the workpiece is
pinched between the saw blade and rip fence and
finally pushed out toward operator. The line 3 varies
by thickness of workpiece or the table level. Adjust
the position of the rip fence according to the thick-
ness of the workpiece.
After adjusting the rip fence, tighten the clamping
screw (A) firmly. (Fig. 24 & 25)
16
All manuals and user guides at all-guides.com
NOTE:
• There are four patterns to position the rip fence as
• To change the rip fence pattern, remove the rip fence
To change from the pattern A or B to the pattern C or D,
or in adverse case, remove the square nut, washer and
clamping screw (A) from the rip fence holder, then posi-
tion the clamping screw (A), washer and square nut on
the opposite position of the rip fence holder compared to
the original position. Tighten the clamping screw (A)
securely after inserting the square nut of the rip fence
holder into the rip fence slit. Insert the square nut on the
rip fence holder into the back end of either slit of the rip
fence so that they fit as shown in the figure. (Fig. 27)
The rip fence is factory adjusted so that it is parallel to
the blade surface. Make sure that it is parallel. To check
to be sure that the rip fence is parallel with the blade.
Lower the table to the lowest position so that the blade
appears at the topmost position from the table. Mark one
of the blade teeth with a crayon. Measure the distance
(A) and (B) between the rip fence and blade. Take both
measurements using the tooth marked with the crayon.
(Fig. 28) These two measurements should be identical. If
the rip fence is not parallel with the blade, proceed as fol-
lows: (Fig. 29)
1.
2.
3.
CAUTION:
• Be sure to adjust the rip fence so that it is parallel with
• Be sure to adjust the rip fence so that it does not con-
Dust bag
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust nozzle. (Fig. 31)
NOTE:
• In miter saw mode, always insert the dust bag to the
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove par-
ticles adhering to the insides which might hamper further
collection. (Fig. 32)
shown in the figure. (Fig. 26) Rip fence has two slits on
its sides, one slit with an elevated fringe nearby on the
same side and the other without it. Use the surface of
rip fence with this fringe facing the workpiece only
when cutting off into a piece of a thin workpiece.
from the rip fence holder by loosening the clamping
screw (A) and change the facing of the rip fence to the
rip fence holder so that the rip fence faces the rip fence
holder according to your work as shown in the figure.
Insert the square nut on the rip fence holder into the
back end of either slit of the rip fence so that they fit as
shown in the figure.
Turn two adjusting screws counterclockwise.
Shift the back edge of the rip fence slightly to right or
left until it becomes parallel with the blade.
Tighten the two screws on the rip fence firmly.
the blade, or a dangerous kickback condition may
occur.
tact the top blade guard or saw blade. (Fig. 30)
back nozzle only.