Bavaria BCD 12/2 Li Instructions D'origine page 15

Weight: .......................................................1.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ....................... 81 dB (A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 92 dB (A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Drilling in metal
Vibration emission value a
K uncertainty = 1.5 m/s
Screwing without hammer action
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_BCD_12_2_Li_SPK9.indb 15 Anl_BCD_12_2_Li_SPK9.indb 15
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Be sure to read the following information before
you put the cordless screwdriver into operation:
≤ 2.5 m/s
2
1. Charge the battery only with the charging unit
h
2
supplied.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
≤ 2.5 m/s
2
faultless condition.
h
2
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
6. Operation
6.1 Charging the battery (Fig. 2-3)
1. Take the rechargeable battery pack (5) out
of the handle (Fig. 2), pressing the pushlock
button (8) at the side to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate.
3. Plug the charging adapter (6a) in the socket.
The red LED on the charging adapter (6a)
then comes on.
4. Push the charger (6b) onto the battery pack
(5). The red LED will come on to indicate that
the battery pack is being charged.
5. When the charging period is completed after
approx. 3-5 hours, the red lit LED will go out
again and the green LED will begin to shine.
If only the red LED blinks, the battery is defective.
Remove the battery. A defective lithium-ion batte-
ry pack is not allowed to be used any more.
The temperature of the battery (5) may rise during
the charging operation. This is normal.
- 15 -
13.04.2018 09:44:15 13.04.2018 09:44:15