Table des Matières
Publicité
en
Ú
Installation instructions
Safety precautions
Read the appliance instructions before installing and using.
The graphics in these Assembly instructions are given as a
guide only.
The manufacturer is exempt from all liability if this manual's
requirements are not complied with.
All operations relating to installation, regulation and
conversion to other gas types must be carried out by an
authorised installation engineer, respecting all applicable
regulations, standards and the specifications of the local gas
and electricity providers.
You are recommended to contact the Technical Assistance
Service to convert to another gas type.
Before you begin, turn off the appliance's electricity and gas
supply.
This appliance has been designed for home use only, not for
commercial or professional use. This appliance cannot be
installed on yachts or in caravans. The warranty will only be valid
if the appliance is used for the purpose for which it was designed.
Before installing, check that local distribution conditions (gas
type and pressure) and the appliance's adjustment are
compatible (see table I). The appliance's adjustment conditions
are written on the label or the specifications plate.
This appliance can only be installed in a well-ventilated place in
accordance with existing regulations and ventilation
specifications. The appliance must not be connected to a
combustion product removal device.
The supply cable must be attached to the unit to prevent it from
touching hot parts of the oven or hob.
Appliances with electrical supply must be earthed.
Do not tamper with the appliance's interior. If necessary, call our
Technical Assistance Service.
Before installing
This appliance is class 3 type, according to the EN 30-1-1
regulation for gas appliances: built-in appliance.
These individual appliances can be combined with other
identical appliances and/or with conventional hobs of the same
make, using the joint accessory. See the catalogue for details.
The units next to the appliance must be made of non-flammable
materials. The laminated covering and glue for adhering it must
be heat resistant.
This appliance cannot be installed above fridges, washing
machines, dishwashers or similar.
An oven must have forced ventilation to install a hob above it.
Check the dimensions of the oven in the installation manual.
If an extractor fan is installed, you must follow the installation
manual's instructions, always keeping a minimum distance of
650 mm to the hob.
Preparation of the kitchen unit (fig. 1-2)
Make an appropriate size cut in the work surface.
If the hob is electric or mixed (gas and electricity) and there is
no oven below, place a non-flammable separator (e.g. metal or
plywood) 10 mm from the bottom of the hob. This will prevent
access to the base of the hob.If the hob is gas, it is
recommendable to place the separator at the same distance.
On wood work surfaces, varnish the cutting surfaces with a
special glue. This protects them from moisture which could
collect under the work surface.
Installation of appliance (fig. 3)
Note: Wear protective gloves to fit the hob.
The clips and adhesive seal (underside of the hob) are factory-
fitted: Do not remove these under any circumstances: The
adhesive seal prevents water seepage.
In order to fit the appliance into the kitchen unit, first place the
hob in the correct position then loosen each of the clips so that
they all turn freely (it is not necessary to completely undo them).
Insert and centre the hob.
Press the sides of the hob until it is supported around its entire
perimeter.
Turn the clips and tighten them fully. Fig. 3.
Removal of hob
Turn off the appliance's electricity and gas supply.
Unscrew the clips and proceed in the reverse order to
installation.
Gas connection (fig. 4)
The gas connection must be located in a position where the
stop tap is accessible.
The end of the inlet connection point of the gas hob has a 1/2"
thread (20.955 mm) that allows for:
A fixed connection.
■
Connection using a flexible pipe (L min. 1 m - max. 3 m).
■
In this case, it is necessary to insert the accessory (427950)
and the watertight seal (034308) supplied between the manifold
outlet and the gas supply. Fig. 4a.
Publicité
Table des Matières
