Shure SM87A Mode D'emploi page 2

OPERATION
Power
The SM87A requires phantom power. This may be supplied
to the microphone from an external power supply (such as the
Shure model PS1A) or directly from preamplifiers, mixers, or
consoles with built-in phantom power. Suitable sources should
provide 11 to 52 Vdc phantom voltage.
Proximity Effect
Unidirectional microphones such as the SM87A progressive-
ly boost bass frequencies by 10 to 15 dB at 100 Hz when the
microphone is at a distance of about 6 mm (1/4 in.) from the
sound source. This phenomenon, known as proximity effect,
can be used to create a warmer, more powerful sound. To pre-
vent explosive low frequency sound during close-up use, the
SM87A bass response gradually rolls off. This provides greater
control and helps the user take advantage of proximity effect.
Wind Noise
The SM87A has an integral wind and pop filter which pro-
vides excellent protection against most wind and breath noise.
Under adverse conditions, such as high winds or close proximi-
ty to a "problem" vocalist, the optional foam windscreen can be
used.
Impedance
A minimum load impedance of 800 ohms should be used
for maximum signal handling and minimum distortion. The load
may be as low as 150 ohms, but a reduction in output signal
strength and output clipping level will result.
SPECIFICATIONS
Cartridge Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz (see Figure 2)
Polar Pattern
Supercardioid (see Figure 3)
Output Impedance
Rated at 150 ohms (100 ohms actual 20%)
Recommended minimum load impedance: 800 ohms
Sensitivity (at 1,000 Hz)
Open Circuit Voltage . . . . . . . . . . . . . . .
Clipping Level (at 1,000 Hz)
1000 ohm Load . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum SPL (at 1,000 Hz)
140.5 dB (0.25% THD, 1000 ohm load)
Self-Noise (equivalent sound pressure level; measured with true
r ms voltmeter)
24 dB typical, A-weighted
26 dB typical, weighted per DIN 45 405
–52.5 dBV/Pa (2.4 mV)
(1 Pa = 94 dB SPL)
–6 dBV (0.5 V)
2
Dynamic Range
116.5 dB (maximum SPL to A-weighted noise level)
Signal-to-Noise Ratio
70 dB at 94 dB SPL (IEC 651)*
Polarity
Positive pressure on diaphragm produces positive voltage on pin
2 relative to pin 3
Power
Phantom Supply Requirement
Current Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector
Three–pin (XLR) professional audio
Case
Aluminum construction with steel grille and satin black finish
Dimensions
See Figure 4
Net Weight
200 grams (7 oz)
*S/N ratio is difference between 94 dB SPL and equivalent SPL of self–
noise A-weighted.
CERTIFICATION
Conforms to European Union directives, eligible to bear CE
marking; meets European Union EMC Immunity Requirements
(EN 50 082–1, 1992).
FURNISHED ACCESSORIES
Swivel Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carrying/Storage Bag . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONAL ACCESSORIES
Phantom Power Supply
Isolation Mount . . . . . . . . . . . . . . . . . . . . . . .
Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable (7.6 m [25 ft]) . . . . . . . . . . . . . . . . . . . . . . . . . . .
REPLACEMENT PARTS
Screen and Grille . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge and Shock Mount
Replacement Amplifier Assembly
TROUBLESHOOTING
If problems arise, test the phantom power source and
connectors before calling for service. The microphone will
not operate without phantom power.
Check the voltage on pins 2 and 3 of the XLR connector
going to the microphone. The voltage at pins 2 and 3 with ref-
erence to pin 1 should be between 11 and 48 Vdc.
For additional service or parts information, please con-
tact Shure's Service department at 1–800–516–2525. Out-
side the United States, please contact your authorized
Shure Service Center.
. . . . . . . . 11 to 52 Vdc, positive
at both pins 2 and 3
1.0 to 1.2 mA
. . . . . . . . . . . . . . . . . . . . . . . .
A53M, A53HM
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
A25C
26A13
PS1A
A85WS
C25F
RK214G
R128
RK356