Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4
Electrical connection
- ELECTRICAL SAFETY :
Operate this machine only on a
supply equipped with a 30 mA
earthed current-limiting circuit-
breaker. Otherwise, consult our
catalogue for appropriate models.
- The RCCB must be used cor-
rectly, including testing it regu-
larly. For tools supplied with an
integral RCCB in the cable or in
the mains plug, if the cable or
plug has been damaged, repairs
must be carried out by the
manufacturer, one of his agents
or by a qualified repair work-
shop to avoid any risks resul-
ting from errors.
• Motor power supply : reinforced electric
cable
with
4
(3xPx+xE)
(3xPx+xNx+xE) conductors 2.5 mm
lengths less than 100 m.
• Earthing of the machine (mandatory).
5
Fitting the tool
Motor off
Disconnect by removing the plug.
• Mixers have an M14 internal thread. Keep
the thread and the external surfaces
clean.
• If the mixer becomes loose, tighten with a
22 mm open ended spanner
• Clean your tools thoroughly to work better
and more safely.
6
Starting
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches from floor and machine
The machine has an electronic speed
control which prevents material flying when
the machine is turned on.
The speed may be controlled by varying the
pressure exerted on the controls.
• Momentary action switch :
¤ On : press the switch
¤ Off : release the switch
• Latching switch :
¤ On : press the switch and latch it using
the button
¤ Off : press the switch again and release
it
• During operation, always hold the machi-
ne in both hands and work in a stable
position.
• Protect yourself against electrical dischar-
ge. Do not touch equipment that is ear-
thed such as conduits, radiators . . .
• Always keep the machine cable behind
you.
or
5
2
for
7
Important advice
• Retighten the bolts regularly, in particular
after the first hours of use.
The manufacturer declines all res-
ponsibility for loss or damage
resulting from misuse or any
modification, alteration or powe-
ring that does not conform to the
manufacturer's original specifica-
tions.
At the work station, the sound
pressure level may exceed 85 db
(A)
In this case individual protection
measures must be taken.
8
Servicing and maintenance
The machine is designed to require only
minimum servicing and maintenance.
Make sure that the following points are
observed :
• Keep the machine clean.
• Do not allow any foreign body to penetra-
te into the electrics.
• After about every 300 hours of use have
the brushes inspected by a specialist. If
they are less than 5 mm long, replace with
new brushes. The brushes should be ope-
rated off load for about 20 minutes.
• At the same time, also check the condition
of the commutator. If the blades are not
uniform in colour and there are surface
stripes, the machine should be sent to an
approved workshop.
• The gear box and drive shaft should be
cleaned after 500 hours of operation.
• At this stage, the whole machine requires
servicing and should be sent to an appro-
ved workshop.
9
Repairs
Contact your supplier who is enti-
S
rely at your service to carry out
A
V
repairs in the shortest time at the
best possible price.
10
Spare parts
For rapid delivery of spares and in order to
avoid any wasted time, it is necessary to
remind your supplier of the details shown on
the instruction plate on the machine with
each order, as well as the reference of the
part to be replaced.
11
Scrapping
In the event of deterioration and
scrapping of the machine, the fol-
lowing items must be disposed
of in accordance with the require-
ments of the legislation in force.
• Main materials :
¤ Motor : Aluminium (AL) - Steel (AC),
Motor :
Copper (CU) - Polyamide (PA)
¤ Machine : Steel sheet (AC) -
¤ Machine :
Cast iron (FT) -
¤ Machine :
Aluminium (AL)
The instructions for use and spare
parts found in this document are for
information only and are not binding.
As part of our product quality improve-
ment policy, we reserve the right to
make any and all technical modifica-
tions without prior notice.
8
Publicité
Table des Matières
