Publicité
Les langues disponibles
Les langues disponibles
Attention: Product not suitable for use with carbon handlebars.
Please read these instructions carefully. Only correctly installed Ergon grips allow for optimum
function. Ergon GS2 grips require a handlebar with 22.2 mm diameter in the grip area and
uninterrupted bar space of 135 mm (5.3") each side. Only handlebars that have been approved by
their manufacturer for use with bar ends should be used and can withstand the required clamping
1.
Mounting area
• left grip 135 mm (5.3") / right grip 135 mm (5.3")
135 mm
2.3
Fit the grip
Push the grip and bar end on to the bar
as far as the mark (Fig. 2.1). Only by
following these steps can a proper install
be ensured.
3.2
Position of the bar end / grip body
The default position for the support platform is horizontal. For fine tuning according to rider
and riding style, please refer to the step 3.1 and the tips given below.
0° to +30°
Attention:
Before riding the bike, please ensure that the grips are properly tightened. If the maximum quoted
7 Nm (5.2 ft-lb) torque is not sufficient to prevent the grips and barends being turned by hand then
the handlebar is not compatible with this product. Please replace the handlebar with one which is
completely round at the end and meets the industry standard of 22.2 mm in diameter. Following
any crashes or impacts, please check the bar ends for damage. Check to see that the grips and
bar ends are still secure. Replace if necessary. In the event of any questions, please contact your
local retailer. Before riding for the first time, ensure that the function of the brakes and gears has
not been restricted without having to change your hand position and that all functions of the bicycle
can be used as normal. A secure fit can only be guarantied with the use of the correct Ergon bar
end.
Maintenance:
In order to ensure that your Ergon grips provide you with the best performance please clean them
regularly using warm soapy water. Rinse thoroughly. Do not use petroleum based products or
solvents, oil or grease on the grips for any reason.
Warranty:
The clamping system used on these grips exceeds the DIN standard 14766 for handlegrips of
70 N removal force. The function and construction of Ergon handlebar grips are covered by a
warranty for two years from the date of purchase. Please be aware that grips do naturally wear
out with use. In the event of a suspected warranty issue, please contact your retailer. Damage as
a result of crashes, misuse, incorrect installation or modification of the grip is not covered by this
warranty.
Information:
Ergon grips offer pain prevention through optimized pressure distribution. This is realised through
the 40% larger surface area. This pressure distribution allows better blood circulation, which may
cause the hands to appear flushed.
135 mm
2.4
Tighten the clamp
Tighten the downward facing clamping
screw so that the grip and bar end can
still be moved.
-15° to +25°
force. Do not use with carbon handlebars. Very thin walled aluminium handlebars should only be
used if manufactured for use with bar ends. Please ensure prior to fitting that the bar is suitably
cleaned using alcohol or other degreasers.
2.1
Mark the mounting area
Measure and mark the handlebar from
the end to the required assembly area of
135 mm (5.3") (Fig. 1). Tip: Use either
sticky tape or a pencil.
3.1.
Grip Position
Turn the grip so that the support platform completely supports the ball of your hand. The
wrist should be in a neutral position avoiding an exaggerated kink. After a short period of
trial and error a comfortable position can be found. Be sure to tighten the clamp with 7 Nm
(5.2 ft-lb) before your first ride.
4.
Final Tightening
Tighten to 7 Nm (5.2 ft-lb) torque using a 4 mm torque wrench.*
7 Nm (5.2 ft-lb)
4 mm
* Attention: Product not suitable for use with carbon handlebars.
Maximum recommended torque: 7 Nm (5.2 ft-lb)
The grips and bar ends should not turn on the bar.
Use only the specified tools to assemble.
Re-check the torque setting following the first ride / 50 km of riding.
Check periodically to ensure that the screws are not loosening.
The correct position for your Ergon grips is an individual thing. Repeat steps 3.1 to 4 adjusting the
angle of the grips in small steps. The angle maybe different for the left and right hand. Ride a test
course to allow good comparison.
Should you suffer from pain or numbness in your hands or forearms despite use of Ergon grips it
may help to try a handlebar with a different profile, or rotate your existing one. If problems persist,
it is advisable to check your position on the bike including frame size, handlebar height and saddle
position with the help of a professional.
Allergy information:
All Ergon grips are latex free.
( GB / US )
2.2
Grip assembly
Loosen the downward facing clamping
screw. Fit the bar end to the grip. You will
hear a distinct "click" when the integrated
security ring engages. This signals that the
bar end is properly fitted to the grip.
Click!
Publicité
