Dust Extraction - Bosch GBR 15 CAG Professional Notice Originale

OBJ_BUCH-2019-001.book Page 19 Wednesday, September 11, 2013 9:22 AM
A plastic part (O-ring) is fitted around
the centring collar of mounting flange
14. If the O-ring is missing or dam-
aged, the mounting flange 14 must be
replaced before resuming operation.
Place the diamond cup wheel 15 on the mounting flange 14.
Pay attention that the direction-of-rotation arrow on the dia-
mond cup wheel agrees with the direction-of-rotation arrow
on the guard and extraction hood 3.
Press the spindle lock button 9 to lock the grinding spindle.
Screw on the clamping nut 16 and tighten it with the two-pin
spanner 18.
Pay attention that the collar of the clamping nut 16 faces away
from the machine, as shown in the figure.
 After mounting the diamond cup wheel and before
switching on, check that the diamond cup wheel
is correctly mounted and that it can turn freely.
Make sure that the diamond cup wheel does not graze
against the guard and extraction hood or other parts.
Changing a Diamond Cup Wheel
When transporting the machine, the diamond cup wheel 15
should be removed to avoid damage to it.
 Do not touch diamond cup wheels before they have
cooled. Diamond cup wheels become very hot while work-
ing.
Press the spindle lock button 9 to lock the grinding spindle.
 Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may be-
come damaged.
Loosen the clamping nut 16 with the two-pin spanner 18 and
unscrew the clamping nut. Remove the diamond cup wheel 15.
Quick-clamping Nut
For convenient changing of grinding tools without the use of
additional tools, you can use the quick-clamping nut 17 in-
stead of the clamping nut 16.
 Use only a flawless, undamaged quick-clamping nut 17.
 When screwing on, pay attention that the side of the
quick-clamping nut 17 with printing does not face the
diamond cutting disc; the arrow must point to the index
mark 19.
19 17
nut with pliers. Always use the two-pin spanner 18.
Bosch Power Tools

Dust Extraction

 Dusts from materials such as lead-containing coatings,
The vacuum cleaner must be approved for the extraction of
masonry dust. Bosch provides suitable vacuum cleaners.
Insert a vacuum hose 10 (accessory) into the vacuum connec-
tion 8. Connect the vacuum hose 10 to a vacuum cleaner (ac-
cessory). An overview for connecting to a vacuum cleaner can
be found at the end of these instructions.
Notes for the Use of Concrete Grinders
Please observe the following notes in order to reduce the dust
emissions occurring while working.
– Only use combinations of diamond cutting discs, concrete
– Observe the operating instructions of the vacuum cleaner
– Only use vacuum hoses as intended for by Bosch. Do not
– Use the concrete grinder only as intended for.
– Observe the general requirements for construction sites.
– Provide for good ventilation.
Lock the grinder spindle
– Ensure that the work area is free of obstructions. For long-
with the spindle lock button
9. To tighten the quick-
clamping nut, firmly turn
– Wear hearing protection, protective goggles, dust mask
the diamond wheel disc in
clockwise direction.
A properly attached, un-
– Use a suitable vacuum cleaner for cleaning the workplace.
damaged quick-clamping
nut can be loosened by
hand when turning the
knurled ring in anticlock-
wise direction. Never loos-
en a tight quick-clamping
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– To achieve a high degree of dust extraction, use the
GAS 50 MS vacuum cleaner for mineral dust together
with this power tool.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
grinders with mounted guard and extraction hood as well
as dust category M vacuum cleaners that are recommend-
ed by Bosch. Other combinations can lead to insufficient
dust collection and separation.
for maintenance and cleaning of the vacuum cleaner, in-
cluding the filter. Empty dust collection containers imme-
diately once full. Clean the filters of the vacuum cleaner
regularly and always insert the filters completely into the
vacuum cleaner.
manipulate the vacuum hose. When rocks or chunks of
stone/masonry are drawn into the vacuum hose, cease
work and clean the vacuum hose immediately. Prevent the
vacuum hose from being bent or creased.
er grinding jobs, the vacuum cleaner must be able to move
along freely and at the right time.
and gloves as required. As dust mask, use at least a parti-
cle-filtering class FFP 2 half-mask.
Prevent settled dust from being swirled up by sweeping.
English | 19
3 609 929 C68 | (11.9.13)