Publicité
Les langues disponibles
Les langues disponibles
Learning the radio code with the remote control
To learn the personalised radio code to the siren with the remote control, carry out
the following procedure:
"Bip"
)
)
)
)
)
BP1
Briefly press
Press and hold
(less than 2 sec)
the "Off" key
The BP1 button
of the remote control
In the siren
until a response comes
from the siren
Learning the radio code with the keypad
To learn the personalised radio code to the siren with the keypad, carry out the fol-
lowing procedure:
"Bip"
)
)
)
)
)
BP1
Briefly press
Send 2 consecutive "Off" commands
(less than 2 sec)
(wait for 2 sec between each press)
The BP1 button
from the keypad
In the siren
until a response comes
from the siren
All manuals and user guides at all-guides.com
"Biiiiip"
)
)
)
)
)
A
10 s
The siren confirms
the learning with
a long validation
beep
"Biiiiip"
)
)
)
)
)
2 s
10 s
The siren
confirms
the learning
with a long
validation
beep
GB
FIG. H
Mounting
Caution: The tamper protection for the removal, the opening of the housing and
the cutting of the antennas is inactive at the time of installation of the siren. It
becomes active after the first arming command (partial or total) is received and if the
tamper actuator is engaged for more than 5 secs. It is strongly advised to wait until
the siren is fixed to the wall before sending any arming commands.
Close the battery compartment flap and clip it shut.
1
Connect the strobe cables
Place the lid on the base of the siren. Turn it over: if the tamper siren sounds,
2
press the OFF key of your remote control or your keypad. Screw the base of the siren
to the lid with its 3 screws.
Use the cardboard drilling template supplied with the siren to mark the 2 siren
3
fixing points and the 2 fixing points for the anti-tamper disc on the wall.
Drill the 4 holes previously marked.
4
Use the 2 supplied wall plugs for fixing the siren (or others better suited if necessary).
5
Use the 2 supplied wall plugs for fixing the wall anti-tamper disc and fix it using
6
the 2 countersunk screws supplied (or others better suited if necessary).
Present the siren to its mounting location with its antennas downwards while
7
assuring that the anti-tamper actuator locates itself correctly inside the anti-tamper
wall disc.
Fix the siren using the 2 round headed screws supplied (or others better suited if
8
necessary).
Send an ON command (Partial, Total, Group 1 or Group 2): the siren gives out
9
one audible signal. Send an OFF command. The tamper protection is now active: if
you remove the siren from the wall, the siren will sound.
Your siren is now installed. Make a real test by triggering your siren in the normal way.
NB: on intrusion, the alarm siren activates 10 sec after the triggering of the integra-
ted siren in the control panel.
BATTERY STATUS AND REPLACEMENT SECTION
The alarm siren checks the state of its batteries permanently. It signals when you must
change them with a harsh audible message
each time an ON or OFF command is made. Change all six batteries at the same
time while adhering to the following procedure:
Select a remote control and a crosshead screwdriver and place yourself at a
1
height to enable you to open the siren.
Remove the two screws that fix the siren to the wall.
2
Remove the siren while simultaneously pressing the
3
control or keypad to limit the length of sounding owing to the triggering of the anti-
tamper switch, open the siren according to the procedure described in
Remove all the batteries and wait 5 min before connecting the new batteries
4
according to the procedure described in
Fix the siren while following the procedure described in
5
Send an ON command (Partial, Total, Group 1 or Group 2) then an OFF com-
6
mand.
Test the siren by carrying out a real triggering.
7
Your siren is ready for operation again.
26
as indicated in
Fig.F
"beep, beep,... beep, beep..."
OFF
key of your remote
Fig.
F.
Fig.
H.
GB
Fig.
B.
27
Publicité
