Taymor INFINITY 06-4579P Instructions D'installation

INSTALLATION INSTRUCTIONS
INFINITY 06-4579P
SINGLE HANDLE LAVATORY FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable
Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
TURN OFF
GASKET & FAUCET INSTALLATION
3
A) Apply a bead of plumber's putty or silicone caulk around the sink openings.
B) Install the gasket over the three holes in your sink.
C) Install faucet shanks through the holes of the sink. Centre the faucet body on the sink.
D) From underneath the sink, secure faucet to sink using bolt (1), cam (2) and nuts (3) provided.
Don't use plumber's putty on cultured marble or other composite sinks.
Putty will discolour the sink.
A
D
1
2
3
All manuals and user guides at all-guides.com
Your installation may require new supply
lines. (Supply lines are not included.)
Safety goggles
Torque wrench Plumber's putty
TURN OFF
B C
Don't over tighten
ATTACH THE HOT AND COLD SUPPLY LINES
4
Apply teflon tape onto threaded ends of faucet inlets.
Connect water supply lines to faucet inlets. Hot water supply lines go into left inlet. Cold water supply
lines go into right inlet. (Supply lines, coupling nuts and fittings are not included)
FOR BRAIDED PLASTIC AND BRAIDED
STAINLESS STEEL SUPPLY TUBES
THESE SUPPLY TUBES HAVE INTEGRAL NUTS, SO JUST
SCREW THE NUT ONTO THE FAUCET INLET.
TORQUE
22 – 30 FT/LBS.
INSTALLING POP-UP DRAIN
5
A) Remove pop-up plunger (A) and flange (B). Screw locknut (C) all the way down. Push
gasket (D) down. Apply silicone to underside of flange (B).
B) Insert body into sink (from underneath). Screw flange onto body. Pivot hole (E) must face
the back of the sink.
C) Tighten locknut (C) and gasket but do not overtighten. Remove pivot ball retaining nut (E).
D) Slide pivot rod (F) into the eye of the pop-up plunger (A). Hand tighten retaining nut.
E) Slide pivot rod (F) through hole in spring clip (G), then through lever strap (H) and back
Silicone caulk
through spring clip.
F) Insert lift rod (I) down through faucet body and then into lever strap (H). Tighten screw (J).
Connect assembly to drain.
A
A
B
D
C
B
A
D
A
FLUSHING & AERATOR CLEANING
6
Remove the aerator by turning it counterclockwise. Remove the internal parts of the aerator by push-
ing them out with your fingers. Remove any debris. Turn on hot and cold water supplies. Turn faucet
handle all the way on and run water through the spout for about a minute to remove debris. While
water is running check all connections for leaks. Reassemble the aerator and screw it back into the
spout hand tight.
EXPLODED DIAGRAM FOR REFERENCE
7
MAINTENANCE Your new faucet is
designed for years of trouble-free
performance. Keep it looking new
by cleaning it periodically with a sof
cloth. Avoid abrasive cleaners, steel
wool and harsh chemicals as these
will dull the finish and void your
warranty.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
FOR 3/8" O.D. BALL-NOSE SUPPLY TUBES
IF THE SUPPLY TUBE END HAS A BULBOUS SHAPE, USE
TORQUE
22 – 30 FT/LBS.
B
B
E
E
H
F
F
G
1-HANDLE
2-SET SCREW
3-INDEX
4-CAP
5 - RING
6 - CAM
7 - CAM INSET
8 - STAINLESS STEEL BALL VALVE
9 - VALVE SEAT
10 - SPRING
11 - ESCUTCHEON
14 - AERATOR ASSEMBLY
12 - BODY
WASHER
AERATOR
AERATOR
SHELL
13 - BASE PLATE
15 - MOUNTING PLATE
16 - SCREW
17 - PLAQUE
18 - SCREW
19 - BOLT
20 - CAM
21 - MOUNTING NUT
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
COUPLING NUTS.
C
E
C
F
1
3
2
LIFT ROD KNOB
LIFT
ROD
FLANGE
LIFT
STRAP
NUT SPRING
CLIP
DRAIN
23 - POP-UP ASSEMBLY
REV. JULY, 2016