Complete Installation - Whirlpool KEMD378SBL00 Instructions D'installation

2. Push against seal area of front frame to push oven into
cabinet.
3. Push oven completely into cabinet and center oven into
cabinet cutout.
4. Securely fasten oven to cabinet using the #8-14 x 1" screws
(2 for single oven, 4 for double oven) provided. Insert the
screws through holes in mounting rails. Do not overtighten
screws.
A
B
A. Mounting rail
B. Insert #8-14 x 1" screw.
5. On some models, the oven vent is taped to the side of the
oven.
With one #8-14 x ³⁄₈" screw for each side of the vent, fasten
vent securely to the oven.
A
A. #8-14 x
B. Oven vent
6. Replace oven racks.
7. Replace oven door(s) by inserting ends of hinges into hinge
slots in the oven frame.
8. Push hinges in as far as they will go and open the oven door.
You should feel the oven door drop into place.
9. Rotate both hinge latches back to the locked position.
10. Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See "Remove
Oven Door" section.
11. Reconnect power.
6
B
³⁄₈
" screw
12. Display panel will light briefly, and "PF" should appear in the
display.
13. If display panel does not light, please reference the
"Assistance or Service" section of the Use and Care Guide or
contact the dealer from whom you purchased your oven.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. For oven use and cleaning, read the Use and Care Guide.
Check Operation of Lower Oven
1. Turn power on.
2. When "CLOCK ENTER TIME" appears in the lower oven
display touch START.
3. Touch BROIL.
4. Touch START.
If oven does not operate, check the following:
Household fuse is intact and tight; or circuit breaker has
not tripped.
Electrical supply is connected.
See "Troubleshooting" section in the Use and Care Guide.
5. When oven has been on for 5 minutes, feel for heat.
If you do not feel heat or if an error code ("F" followed by a
number plus "E" followed by a number) appears in the
display, turn off the oven and contact a qualified technician.
6. Touch LOWER OVEN OFF.
Check Operation of Microwave Oven
1. Fill a microwave-safe container with 1 cup (250 mL) of water
and place container inside microwave oven. Close door
firmly.
2. Set microwave oven cook time to "2:00" minutes.
3. Touch START. The interior microwave oven light should be on,
and the remaining cooking time should be displayed in the
upper oven display.
If microwave does not operate, check the following:
Household fuse is intact and tight; or circuit breaker has not
tripped.
Electrical supply is connected.
See "Troubleshooting" section in the Use and Care Guide.
When display reads "1:00" minute, open microwave oven
door. The microwave should stop cooking. Close door firmly.
The interior microwave oven light should turn off.
4. Touch START to resume preset cycle. The microwave oven
should begin cooking, and the microwave oven interior light
should be on.
Let microwave oven complete cooking time. A tone will
sound 3 times at the end of the cooking time, and the
microwave oven will shut off.
5. Open microwave oven door and slowly remove container.
Water in container should be hot.
If you need Assistance or Service:
Please reference the "Assistance or Service" section of the Use
and Care Guide or contact the dealer from whom you purchased
your built-in and microwave ovens.