Publicité
7200
R) Removable connection terminal block:
1:
Receiver
2:
Microphone
3:
Common voice line
4:
Auxiliary service activated using
terminal 5)
5:
Negative power supply from main power supply unit type 6680 or ad-
ditional power supply unit type 6582
6:
Positive power supply from main power supply unit type 6680 or ad-
ditional power supply unit type 6582 (minimum input voltage 15V DC)
7:
Second auxiliary function activated by
enabled only with microswitch located on rear of monitor in position A)
8:
Call from entrance panel
9:
Command for door lock release, output activated from
button
10: 12V DC output for Elvox video distributor
11: Door call
12: Push-button for audio activation
position A)
13: Green LED power supply (max. positive input voltage 18V DC)
V:
Video signal, input for connection of 75 Ohm coaxial cable
M: Earth for terminal V
SETTINGS AND OPERATING MODES
Selecting the speech unit call melody
The monitor has seven different melodies. To select a different melody from
the default one (ding dang dong), when the monitor is switched off hold
down either of the brightness control push-buttons
) for at least one second, then press the buttons repeatedly to se-
lect the desired melody.
Adjusting the ringtone volume
To adjust the call ringtone volume, hold down either of the volume control
push-buttons
(
and
the buttons repeatedly to increase, decrease or mute the ringtone volume.
Ringtone mute
Ringtone mute is activated using the same procedure described above for
adjusting the ringtone volume. Once the volume has been adjusted to the
lowest setting by repeatedly pressing the down arrow, the red LED
the bottom left-hand corner, illuminates to indicate that ringtone mute is
activated.
Brightness control
Brightness can only be adjusted when the display is switched on. Use the
brightness control push-buttons
brightness. When the maximum and minimum values are reached, this is
indicated by a beep.
Adjusting the conversation volume
The term "conversation volume" refers to the perceived volume of the cal-
ler's voice when he/she is standing in front of the speech unit (entrance
panel). To adjust the conversation volume, hold down the TALK/LISTEN
push-button
and increase or decrease the setting using the volume
control push-buttons
(
and
in HANDS FREE mode and in PUSH-TO-TALK mode.
Communication mode selection function
It is possible to choose one of two different modes of communication with
the speech units:
GB
All manuals and user guides at all-guides.com
push-button (with reference to
push-button (function
push-
(or self-start when switch is in
(
and
), for at least two seconds, then press
(
and
) to select the
). This procedure applies both
1) HANDS FREE mode: press the TALK/LISTEN button
start of the conversation only, to activate the audio, and at the end of
the conversation to deactivate the audio. The "audio active" status is
indicated by illumination of the red LED
of the monitor, which is normally used to indicate RINGTONE MUTE.
2) PUSH-TO-TALK mode: keep the talk/listen push-button
sed during the conversation; release it at the end of the conversation.
The 7200 series monitor is factory set to HANDS FREE communication
mode.
To switch from one mode to the other, hold down both volume control
push-buttons
(
flashing (for around 2 seconds) to indicate entry into ADJUSTMENT mode.
At this point, while the LED is flashing, press the TALK/LISTEN push-but-
ton
to confirm the change. The function is confirmed if the red LED
switches off.
Automatic answer function
This function, which is only available in HANDS FREE mode, activates the
monitor audio connection automatically when a call is received from the
speech unit, without the need to push the TALK/LISTEN button
The "audio active" status is indicated by illumination of the red LED
in the bottom left corner of the monitor, which is normally used to indicate
RINGTONE MUTE. The audio is activated automatically 5 seconds after
the call is received. To enable this function, hold down both brightness
control push-buttons
underneath starts flashing (for around 2 seconds) to indicate entry into AD-
JUSTMENT mode. At this point, while the LED is flashing, press the
TALK/LISTEN push-button to confirm the change. The function is confir-
med if the red LED switches off.
To disable this function, follow the same procedure. If HANDS FREE mode
was not active during the enabling process, it will be activated automati-
cally when the AUTOMATIC ANSWER function is enabled. If the automa-
tic answer function is subsequently disabled, the HANDS FREE function
will remain active.
Self-start function
The monitor can be programmed to self-start on activation of a speech
unit camera by using the
near to the terminal block) is in position B or using the
in
ton if the selector is in position A. If the selector is in position B you can use
the
push-button for sequential switching between cameras with
switching module type 6592.
NOTE: Use of the self-start function is only available if the connection has
been made in the installation.
Conversation privacy programming
Conversation privacy protects the privacy of users in an apartment block,
who would otherwise be able to listen to the calls of other users.
This function is only useful if all of the monitors in the installation are
enabled. The conversation privacy function is activated by holding down
both "
,
" buttons for 2 seconds. When the red LED starts
flashing press the
setting. To turn conversation privacy OFF, follow the above procedure but
using the "
,
in the bottom left corner
and
) until the red LED underneath starts
(
and
) until the red LED
push-button if the A/B selector (located
button until the LED switches off to confirm the
" buttons instead.
at the
pres-
.
push-but-
5
Publicité
