Publicité
Les langues disponibles
Les langues disponibles
MANDATORY CONNECTIONS
1. Disconnect the battery.
2. Connect the "+" terminal of the control box to a 12V positive (+) power source (i.e. fuse box), using
the wire provided in the kit.
Note: Attach this wire to an ignition controlled source to stop the fan when the vehicle is shut off.
Note: Attach this wire to a non-ignition source to keep the fan running after the vehicle is shut off.
3. Connect the "B" terminal to a high amp 12V positive power source (i.e. battery, alternator) using
the wire and in line circuit breaker provided in the kit.
Note: Circuit breaker is marked for proper installation.
4. Connect the "G" terminal to ground (i.e. chassis, negative side of battery) using the wire provided
in the kit.
5. If you have air conditioning: with 3-way connector provided, pass the A/C clutch positive(+)
wire (connected to the A/C pump) through the connector. Place the black wire provided into the
closed end of the connector. Crimp metal plate. Snap plastic cover into place. Attach black wire
to the "C" terminal of the
control box.
Air Conditioning Relay activates fan when A/C is turned on
ADJUSTING THE TEMPERATURE CONTROL
1. Attach the temperature control knob to the
control box.
2. Turn the knob clockwise completely.
3. Idle the vehicle, observe the temperature of
the vehicle. (Use the vehicles gauge)
4. When the temperature of the vehicle reaches
above normal, turn the control knob counter-
clockwise until the fan turns on. From here
on the fan should activate at this tempera-
ture setting. Adjust as necessary according to
your vehicle needs.
OPTIONAL CONNECTIONS
Manual Switch (not included) - Allows
manual operation of the fan.
(This step is based on Flex-a-lite's manual switch part
#31148, other switches may cause this unit to function
improperly.)
1. Connect the "M" terminal to terminal 1 on
the switch.
2. Attach terminal 2 of the switch to a 12V
positive (+) source.
3. Attach terminal 3 of the switch to ground, in
order to illuminate the switch.
Note (optional): To stop the fan from activating
thermostatically, omit the lead to the "+" termi-
nal of the control box.
remain connected.
Flex-a-lite Corporation, P.O. Box 580, Milton, Washington 98354, Telephone No.. 253/922-2700, warrants to the original purchaser User,
all Flex-a-lite products to be free of defects in material and workmanship for a period of 365 days (1 year) from date of purchase. Flex-a-
lite products failing within 365 days (1 year) from date of purchase, may be returned to the factory through the point of purchase,
transportation charges prepaid. If, on inspection, cause of failure is determined to be defective material or workmanship and Not be
misuse, accident, or improper installation, Flex-a-lite will replace the fan free of charge, transportation prepaid. Flex -a-lite will Not be
liable for incidental, progressive, or consequential damages. Some states do Not allow the ex clusion or limitation of incidental or
consequential damages, so the above limitation or ex clusion may Not apply to you. This warranty gives you specific legal rights and you may also
have other rights, which vary from state to state.
NOTE: The Flex-a-lite warranty is in compliance with the Magnuson-Moss Warranty Act of 1975.
"B", "G", & "M" must
THE FLEX-A-LITE LIMITED WARRANTY
Control Box Terminals & Connections
Mandatory Connections
+
12 volt positive source
G Ground
B
12 volt positive source
C
Air conditioning relay
Control Box
C
B
3-way
connector
Circuit
Breaker
12 Volt
Source
12 Volt Positive Source
*WARNING: If not using Flex-a-lite's illumi-
nated switch (PN #31148) you must
disconnect the switch ground.
Optional Connection
M
Manual switch
Ground
G
M
+
12 Volt Positive Source
Ground
(Illuminate switch)
2 of 6
Publicité
