Publicité
Les langues disponibles
Les langues disponibles
enter the new room number;
press button
to confirm;
continue with the next programming or exit
programming.
Programming additional user addresses
(codes 001-004).
In DUO systems, the intercom can also answer
calls addressed to other users, so 4 additional
call addresses can be stored. The storage pro-
cedure is shown below for the first of the four
addresses (code 001). Using codes 002, 003 and
004, the second, third and fourth additional
addresses can be entered respectively.
First additional address (code 001).
To program the first additional call address (by
default empty; permitted addresses between
001 and 200) it is necessary:
enter code 001;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the room numbers of the
additional user addresses (codes 006-
009).
With regard to the 4 additional addresses, the
intercom can act as MASTER or as a second-
ary device (room 001-004) to answer calls
correctly. The storage procedure is shown
below for the room number related to the first
of the four additional addresses (code 006).
Using codes 007, 008 and 009, it is possible to
enter the room numbers for the second, third
and fourth additional addresses respectively.
Room number relative to the first addi-
tional address (code 006).
To program the room number for the first
additional address (by default empty; per-
mitted addresses between 000 and 004), it
is necessary:
enter code 006;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming of addresses activated
by pressing button 1 (codes 010 and
012).
Button 1 on the intercom provides the possi-
bility of activating two different services (each
identified by the relative address) according
to the time for which the button is pressed. In
particular, a distinction is made between short
pressure (<1 sec.) and long pressure (> 3 sec.).
The permitted values for the services that can
be activated are:
- addresses 001-200: call to another user
- addresses 201-210: call to concierge unit;
- addresses 211-220: actuator activation
- addresses 231-253: door lock release (with
handset on hook) or activation of the speech
channel (with handset off), without having
been called, of the door unit;
- address 255: deletion of previously entered
value.
- 10 -
Mi 2576/1
Programming the address associated
with short pressure of button 1 (code 010).
To program the address associated with short
pressure on button 1 (factory setting 211), it is
necessary:
enter code 010;
press button
to confirm;
enter the new address; enter 255 if you want
to restore the empty memory cell;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the address associated
with long pressure of button 1 (code 012).
To program the address associated with long
pressure on button 1 (by default empty), it is
necessary:
enter code 012;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming room numbers related
to the addresses activated by pressing
button 1 (codes 011 and 013).
If the short or long pressure, or both, are as-
signed the same address with which the inter-
com is called from outside, the service that is ac-
tivated is the intercom call within the same flat.
In order to correctly address this call, the room
number associated to the short/long pressure
of button 1 must be programmed with the
room number corresponding to the intercom/
videointercom to be called. Allowed values are:
- address 000-007: room numbers;
- address 255: delete previously entered value.
Programming the room number related
to the address associated with short
pressure of button 1 (code 011).
To program the room number related to the
address associated with short pressure on
button 1 (by default empty), it is necessary:
enter code 011;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the room number related
to the address associated with long pres-
sure of button 1 (code 013).
To program the room number related to the
address associated with long pressure on
button 1 (by default empty), it is necessary:
enter code 013;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming of addresses activated
by pressing button 2 (codes 014 and
016).
Button 2 on the intercom can activate only one
service: the one activated by short pressure
(<1 sec.). In fact, long pressure (> 3 sec.)
activates/deactivates the office function.
If the office function activation time is
equal to 0 "zero" (function disabled), long
press on button 2 activates the function
set with programming codes 016 and 017.
The permitted values for the services that can
be activated are:
- addresses 001-200: call to another user
- addresses 201-210: call to concierge unit;
- addresses 211-220: actuator activation
- addresses 231-253: door lock release
(with handset on hook) or activation of the
speech channel (with handset off), with-
out having been called, of the door unit;
- address 255: deletion of previously entered
value.
Programming the address associated
with short pressure of button 2 (code 014).
To program the address associated with short
pressure on button 2 (by default empty), it is
necessary:
enter code 014;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the address associated
with long pressure of button 2 (code 016).
To program the address associated with long
pressure on button 2 (by default empty), it is
necessary:
enter code 016;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming room numbers related
to the addresses activated by pressing
button 2 (codes 015 and 017).
If the short or long pressure, or both, are as-
signed the same address with which the inter-
com is called from outside, the service that is ac-
tivated is the intercom call within the same flat.
In order to correctly address this call, the room
number associated to the short/long pressure
of button 2 must be programmed with the
room number corresponding to the intercom/
videointercom to be called. Allowed values are:
- address 000-007: room numbers;
- address 255: delete previously entered value.
Programming the room number related
to the address associated with short
pressure of button 2 (code 015).
To program the room number related to the
address associated with short pressure on
button 2 (by default empty), it is necessary:
enter code 015;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Publicité
