Home Position Adjust; How To Control The Unit - Nicols SPLENDOR LED Manuel D'utilisation

exit menu mode without any change after 10 seconds. To go back to the functions without
any change press the MENU button
Show Mode
Press the MENU button up to when the
button, Use DOWN and UP button to select the
1) or (Show 2) or ... or
or automatically exit menu mode without any change after 10 seconds. To go back to the
functions without any change press the MENU button
Sound
Press the MENU button up to when the
button, Use DOWN and UP button to select the
Once select, press ENTER button to setup or automatically exit menu mode without any
change after 10 seconds. To go back to the functions without any change press the MENU
button
Blackout mode
Press the MENU button up to when the
button, Use DOWN and UP button to select the
Once select, press ENTER button to setup or automatically exit menu mode without any
change after 10 seconds. To go back to the functions without any change press the MENU
button.
LED display
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to select
(display off) mode. Once select, press ENTER button to setup or exit menu mode
without any change after 10 seconds. Back to the functions without any change press
MENU button again.
Display Inverse
Press MENU button until is blinking on the display. Use DOWN and UP button to
(inverse), press ENTER button to setup. Back to the
select (normal) or
functions without any change press MENU button.
Self-Test
Press the MENU button up to when the
button and the unit will run the built-in programmer for self-test. To go back to the functions
press the MENU button.
is shown on the display. Pressing ENTER
(Random show) or
(show8). Once select, press ENTER button to store
is shown on the display. Pressing ENTER
(sound on) or
is shown on the display. Pressing ENTER
(blackout) or
is shown on the display. Pressing ENTER
(display on) or
is blinking on the display. Pressing ENTER
18
Fixture Hours
Press the MENU button up to when the
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button.
(show
Software version
Press the MENU button up to when the
button and the display will show the version of software of the unit. To go back to the
functions press the MENU button.
Reset
Press the MENU button up to when the
(sound off).
button and all the motors will back to their home position.

4.2 Home Position Adjust

Press Enter button for about 5 seconds, "OPAN" will shown on the display, press ENTER
button to confirm, then use DOWN and UP button to adjust the home position (-127 - 127)
of the motor. Once the position has been selected, press the ENTER button to setup or exit
the offset mode without any change press the MENU button.
(normal).

5. How To Control The Unit

You can operate the unit in three ways:
1. By master/slave built-in preprogrammed function
2. By easy controller
3. By DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address
setting will be effected at once. Every time you turn the unit on, it will show "L308" on the
display. After that the unit will be ready to receive DMX signal or run the built in programs.
5.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when
you want an instant show. You have to set the first unit in master mode
(random show),
have nothing plugged into it, and Its master LED will be constantly on and sound LED will
flash to the music. The other units will have to select
show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the
slave led lights will constantly on.
is blinking on the display. Pressing ENTER
is blinking on the display. Pressing ENTER
is blinking on the display. Pressing ENTER
(show 1) or ...or (show 8). Its DMX input jack will
(normal) or
19
and select
(2 light