Télécharger Imprimer la page
GE Profile Serie Instructions
GE Profile Serie Instructions

GE Profile Serie Instructions

Gabarit pour panneau sur mesure épais de 19 mm (3/4 po) pour modèle de lave-vaisselle à réglage intégré en haut
Masquer les pouces Voir aussi pour Profile Serie:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Trim Around Dotted Line
2-9/32"
Drill 3/32"
Pilot Hole
3/32" Deep
3/4" Thick Custom Panel
Template Instructions for
Top Control Integrated Profile and
Monogram Dishwasher Models
The custom panel should be sized to your installation situation. See Step 1. For easier
installation the custom panel and custom handle should be attached before installing the
dishwasher. Use this template to locate mounting screws and spacers on the custom panel.
IMPORTANT
• A custom handle must be installed onto the custom
panel. Install the custom handle 4-1/2" max. from
the top of the panel.
STEP 1 CUSTOM PANEL SIZE REQUIREMENTS
HEIGHT
Panel height must be between 30-1/16" and 30-1/4".
23-3/4"
• If the panel height is more than 30-1/4" it will
prevent the door from swinging open.
• If the panel height is less than 30-1/16" it will not
cover the dishwasher door frame.
25-9/16"
STEP 2 DRAW CENTERLINE
• Place the custom panel on a flat surface with appearance side
down.
• Locate the vertical center of the panel at the top.
• Use a carpenters square to draw a centerline from top to bottom.
STEP 3 ALIGN TEMPLATE TO PANEL
• Trim template on the dotted line along all sides.
• Place the template on the panel aligned with the top edge and
the centerline. Use tape to hold in place.
IMPORTANT: If the template is not aligned with the top edge of the
panel, the 1/2" minimum gap will not be maintained. This 1/2" minimum
gap must be maintained to prevent condensation and damage to the
control panel from screw heads.
• Use an awl to mark the screw hole locations indicated on the
template. Remove the template.
STEP 4 INSTALL MOUNTING SCREWS AND SPACERS
If the panel is less than 3/4" thick, shorter screws must
be used. Use #8 x 1/2" screws for 1/2" thick panels (not supplied).
• Use a 3/32" drill bit to drill pilot holes 3/32" deep in the marked
locations.
Note: The custom panel is secured to the dishwasher door with
the spacers and screws provided. The spacer will slip into the
keyhole slots on the dishwasher door.
• Drive the supplied #8 x 5/8" Phillips truss head steel screws
through the spacer and into the panel.
• Install remaining spacers and screws as indicated in the marked
locations.
Drill 3/32"
Pilot Hole
3/32" Deep
Trim Around Dotted Line
Top of Panel
11-5/16"
PARTS INCLUDED:
(4) Spacers
(4) #8 x 5/8" Phillips truss head stainless steel screws
(3) #8 x 1-3/4" Phillips truss head stainless steel
wood screws
(2) Heavy duty springs
• The top of the custom panel must be flush
with the top of the door. The 1/2" minimum gap
between the top of the door and the bottom of the
countertop must be maintained.
Countertop
30-1/16" Min.
30-1/4" Max.
1/2" min.
Minimum 1/2" Gap
for Clearance
WIDTH
Panel width must be 23-3/4".
• If the panel width is less than 23-3/4" it will not
cover the dishwasher frame.
IMPORTANT: To ensure optimum door balance
performance, the custom panel must not weigh more
than 14 lbs.
Mark Center
Screw Holes
Screw
Spacer
Top of Panel
11-5/16"
STEP 5 INSTALL CUSTOM HANDLE
A custom handle must be installed onto the panel
before the panel is secured to the dishwasher door.
• The handle should be installed so that it aligns with
adjacent drawer handles, or 4-1/2" max. from the
top of the panel. Secure the handle in the same
manner as cabinet handles. Screws must be
countersunk into the panel.
STEP 6 INSTALL ASSEMBLED PANEL
• Secure the panel to the door by inserting the top
and bottom mounting screws with spacers into
the matching keyhole slots.
• Make sure all 4 spacers engage the keyhole slots.
• Press the panel against the door and push
downward until the spacers are fully engaged
into the key hole slots. The panel should align
evenly with the top and sides.
• Stand the dishwasher upright.
• Open dishwasher door and drive the supplied
#8 x 1-3/4" truss head screws. Drive one screw at
the top and one on each side as shown, through
the inner door and into the custom panel.
WARNING: Do not overtighten screws. Excessive
tightening of the screws could damage door edges.
STEP 7 INSTALL DOOR SPRINGS
The dishwasher is shipped from the factory with a
temporary set of balance springs. Use the heavy duty
springs provided and the adjustment holes in the
cable to balance the door after the custom panel
is installed onto the dishwasher.
• With the dishwasher on the wood skid, close and
latch the door.
• Remove and discard both door springs.
• Attach the new heavy duty door springs. Engage
the end with the short hook into the support leg
Pulley
and the long hook into the cable.
• Open and close the door.
• If the door drops open when released, increase
Shoulder
spring tension. If the door closes when released,
decrease tension.
TIP: If the door does not open easily or falls too
quickly, check spring cable routing. The cable is held
in place by "shoulders" on the pulley. Check to be
sure the cable has not slipped over the pulley
shoulders.
IMPORTANT: Adjust both balance springs to the
same amount of tension to prevent excessive door
twisting during use.
Trim Around Dotted Line
Trim Around Dotted Line
2-9/32"
Drill 3/32"
Pilot Hole
3/32" Deep
Screws Must
Be Countersunk
Into Panel
4-1/2" Max.
From Top
of Panel
Handle
Custom
Door Panel
Custom
Panel
Dishwasher
Door
Shoulder Washers
Engage Keyhole
Slots
Custom
Panel
25-9/16"
Use This
Mounting
Hole
Decrease
Tension
Increase
Correct Spring
Tension
Cable Routing
Pub. No. 31-30569-1
Dwg. No. 206C1559P109
07-04 JR
Drill 3/32"
Pilot Hole
3/32" Deep

Publicité

loading

Sommaire des Matières pour GE Profile Serie

  • Page 1 Top of Panel Top of Panel Trim Around Dotted Line Trim Around Dotted Line 2-9/32" 2-9/32" 11-5/16" 11-5/16" Drill 3/32" Drill 3/32" Pilot Hole Pilot Hole 3/32" Deep 3/32" Deep STEP 5 INSTALL CUSTOM HANDLE 3/4" Thick Custom Panel Screws Must Be Countersunk Into Panel A custom handle must be installed onto the panel...
  • Page 2 Haut du panneau Haut du panneau Couper le long du pointillé Couper le long du pointillé 5,8 cm 5,8 cm 28,7 cm 28,7 cm Percer un trou Percer un trou guide de guide de 3/32 po à une 3/32 po à une profondeur profondeur de 2,4 mm...

Ce manuel est également adapté pour:

Monogram serieProfile pdw9700lii