Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36466F
Wrenches: 11/16, 13mm,
11/16 Crowfoot adaptor
2
Exhaust, heat shield and
trunk not shown.
1
Qty. (4)
Carriage bolt 7/16-14 X 2.00 GR5
2
Qty. (4)
Spacer
3
Qty. (4)
Conical washer
1.
Remove the two plastic fascia nuts from the fascia tabs (Do not discard).
2.
Lower exhaust by removing bolts holding exhaust hangers both sides.
3.
Remove (4) plastic nuts at the bottom of the trunk holding heat shield in position. Gently pull the heat shield away from the frame rail to allow access to
frame rails. Note: heat shield cannot be removed.
4.
Remove tape covering holes on the side frame rail.
5.
Using pull wires, feed spacers and carriage bolts into position (both rail). Access hole located at end of the frame rail and before the impact bar. Leave pull
wire attached. See Figure 2 A. Note: It is much easier if bolt and spacer are not engaged while inserting them into frame, refer to illustration. See Figure 3.
6.
Push (only) fasteners back into frame rail leaving pull wire and the extra wire sticking out between frame rail and trunk. See figure 2 B
7.
Raise hitch into position between frame rails, feed pull wires thru adjacent holes in the hitch. See Figure 2 B Pointing the receiver tube down and rotating it
into position through the fascia exhaust cut-out and above the muffler and heat shield. Be careful not to scratch fascia. If excess caulking on the frame rail
interferes with hitch installation lower hitch and scrape excess caulking for installation.
8.
Pull fastener back through access holes and hitch.
9.
Remove pull wires and attach conical washers and nut (be careful not to push fastener back into frame rail).
10.
Tighten to specification.
11.
Bend heat shield back into position and re-install heat shield plastic nuts previously removed.
12.
Raise exhaust system back into position.
13.
Reinstall plastic nuts back into bumper fascia.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
Access hole
Impact bar
Fascia
Drawbar must be used in the
RISE position only.
Note: Fasteners typical
both sides
1
3 4
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Volvo S-80
Drawbar Kit:
36061
4 3
2
1
5
Figure 1.
4
Qty. (4)
5
Qty. (4)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Frame rail
Access hole
Impact bar
Kink pull wire to keep block
independent of bolt
Figure 3.
Hex nut 7/16-14
Pull wire
36466N
11-7-07
Part Numbers:
36466
90171
06608
A
B
Figure 2.
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 36466
Sommaire des Matières pour Cequent Towing Products 36466
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007 Cequent Towing Products Sheet 1 of 3 36466N 11-7-07 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2007 Cequent Towing Products Feuille 2 de 3...
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007 Cequent Towing Products Hoja 3 de 3 36466N 11-7-07 Rev.