Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame Rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36407F or 90137F
Wrenches: 3/4
Drill Bits: None
Access Hole
In Cross Member
Both Ends
1234
Fasteners Typical
Both Sides
1
Qty. (4)
Carriage Bolt ½-13 x 1-1/4"
2
Qty. (6)
Block ¼ x 1 x 3
3
Qty. (6)
Conical Toothed Washer ½"
1.
Lower exhaust by removing rubber hangers from hanger brackets. If vehicle is equipped with dual exhaust, lower exhaust both
sides.
2.
Install ½-13 x 1-1/4" lg. carriage bolts and blocks thru access slot and over holes in vehicle frame rail, both sides.
3.
Install ½-13 x 1-3/4" lg. carriage bolts and blocks thru access holes in vehicle cross member and down thru holes in cross
member as shown.
4.
Raise hitch into position. Install conical toothed washers and nuts as shown.
5.
Tighten all ½-13 GR5 fasteners with torque wrench to 75 lb.-ft.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
Chevrolet Impala
Fascia
Drawbar Kit:
36061
Or
90006
Drawbar must be used in the
RISE position only.
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB Max Gross Trailer Weight
300 LB Max Tongue Weight
Wiring Access Location: PC3, PC4
Cross Member
4
Qty. (6)
Hex Nut ½-13
5
Qty. (2)
Carriage Bolt ½-13 x 1-3/4"
Sheet 1 of 3
36407N
Part Numbers:
36407
06389
90137
Vehicle Frame
Rail
Access Slot
In Frame Rail
Typical Both
Side
5234
10-6-05
Rev. A
Form F206 Rev A 5605
Publicité
Manuels Connexes pour Cequent Towing Products 36407
Sommaire des Matières pour Cequent Towing Products 36407
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36407N 10-6-05 Rev. A 2005 Cequent Towing Products Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 36407N 10-6-05 Rev. A 2005 Cequent Towing Products Form F206 Rev A 5605...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 36407N 10-6-05 Rev. A 2005 Cequent Towing Products Form F206 Rev A 5605...